
Video: WIRELESS Messaging in Minecraft 1.17 by Mumbo Jumbo
How to build it
- Set Up the Lectern Book
Place a lectern and insert a written Book and Quill with 15 pages. Write one word or phrase on each page corresponding to the 15 messages you want to be able to send.
- Build the Signal Strength Piston Selector
Take a comparator output from the back of the lectern and run a 15-block redstone dust line alongside a row of 15 sticky pistons. Position solid blocks on the pistons so that the signal strength from your chosen page moves the corresponding number of blocks into place.
- Wire the Dropper Array and Send Button
Place 15 droppers next to the piston blocks and fill each with stacks of dummy items. Wire a send button across all 15 positions so that pressing it only powers the droppers that currently have a piston-pushed block in front of them.
- Install the Hopper Line and Metering Clock
Point all 15 droppers into a shared hopper chain leading toward a chest. Lock the final hopper before the chest with a slow redstone clock so items are released one by one at a steady interval rather than clumping into a single continuous signal.
- Connect the Sculk Sensor Wireless Highway
Read the metered item pulses with a comparator and use them to trigger a trapdoor at the start of your wireless sculk sensor line. Space sculk sensors and trapdoors (using wool occlusion to make them directional) in the air between your two stations; add a second parallel line underneath for two-way communication.
- Build the 15-Lamp Display and Pulse Counter
At the receiving station, place a row of 15 redstone lamps with signs written to match the 15 pages of your lectern book. Behind the lamps, construct a 15-stage resettable redstone pulse counter that shifts the active output one lamp further along with each incoming pulse.
- Split the Incoming Signal into Count and Reset Lines
Take the output from the final receiving sculk sensor and split it into two paths: one path running through a long line of repeaters into the counter's input, and a second path running into a comparator pulse extender.
- Wire the Auto-Reset Monostable Circuit
Connect the output of the pulse extender into a rising-edge monostable circuit tied to the counter's reset line. The extender stays powered continuously while pulses of the same message arrive, ensuring the counter only resets at the very beginning of a brand-new message.
How it works
The system operates in three distinct stages: encoding a page number into timed pulses, transmitting those pulses wirelessly via vibrations, and decoding the pulse count back into a readable display.
- Encoding (Signal Strength to Pulse Count): A lectern outputs a redstone signal strength from 1 to 15 depending on which page is open. That signal strength controls how many of the 15 sticky pistons position conductive blocks in front of the 15 droppers. Pressing the send button fires all enabled droppers simultaneously, dumping N items (where N is the page number) into the hopper pipe.
- Pacing and Wireless Transmission: Sculk sensors have a cooldown period and cannot process rapid pulses. A redstone clock periodically unlocks the hopper at the end of the pipe, letting one item through at a time. Each item creates a spaced pulse that flips a trapdoor, sending a vibration wave down the aerial sculk sensor relay line.
- Auto-Reset and Decoding: When the first pulse of a new message arrives at the receiver, it immediately activates the comparator pulse extender, which triggers a monostable circuit to wipe the previous message on the counter. Simultaneously, the first pulse travels down a long repeater delay line so that the reset finishes before the pulse enters the counter. Because subsequent pulses in the same message arrive before the pulse extender decays, the monostable circuit does not re-trigger mid-message. Once the pulses stop, the final count remains lit on the corresponding redstone lamp.
Tips & variations
- Clock Tuning: Do not speed up the hopper-unlocking clock at the encoder; if items pass through faster than a sculk sensor's cooldown cycle, the wireless line will drop pulses and display the wrong message.
- Pulse Extender Timing: Make sure the comparator pulse extender at the receiver holds its charge slightly longer than the gap between two consecutive pulses from your sender, or the decoder will reset itself in the middle of a message.
- Noise Isolation: Build the aerial sculk sensor highway well above the ground or insulate it with wool so stray player footsteps and mob movements do not inject extra pulses into an active transmission.
- Identical Books: For a two-way setup, copy your Book and Quill so both terminals have the exact same phrases on pages 1 through 15 and matching signs on their lamp boards.




