How a Redstone Repeater Works
A redstone repeater transmits power strictly in one direction: from its back input to its front output. Whenever its back receives a signal of any strength (up to 15), the repeater outputs a full power level of 15 from its front after its set delay.
Valid power sources at the back of a repeater include:
- Active power components (levers, redstone torches, blocks of redstone, etc.)
- Powered redstone dust pointing into it or running past its input
- A powered repeater or redstone comparator facing directly into its back
- Any powered opaque block (including opaque mechanism blocks like dispensers or redstone lamps)
At its front output, a repeater can power redstone dust, activate any mechanism component it faces, power another repeater or comparator facing away from it, or strongly-power an opaque block. Because the opaque block becomes strongly-powered (unlike a block weakly-powered by dust), that block can then power adjacent redstone dust as well as other redstone components.
Placement, Delay Configuration & Pulse Stretching
Repeaters are 0.125 blocks tall and must be placed on top of opaque blocks, glass, furnaces, upside-down slabs, upside-down stairs, or other supported surfaces. If the supporting block beneath a repeater is removed or moved, or if water, lava, or a piston pushes into its space, the repeater breaks and drops as an item. It can also be broken instantly by hand or with any tool.
A faint light-gray arrow on the top texture points toward the front output. The top also holds two small redstone torches that glow bright red when the output is active and turn dark red when off. The gap between these two torches visually indicates the current delay setting (delay block state 1 through 4).
- 1 Redstone Tick (Default): 2 game ticks, or 0.1 seconds (barring lag).
- 2 to 4 Redstone Ticks: Interact with the repeater to cycle the movable torch backward, adding 1 redstone tick per click up to 4 ticks (0.4 seconds), before wrapping back to 1.
Pulse Stretching & Suppression: A repeater set to a delay of 2, 3, or 4 redstone ticks modifies short pulses. It lengthens any incoming ON-pulse shorter than its delay to match its setting (for example, a 4-tick repeater stretches a 1-tick, 2-tick, or 3-tick ON-pulse into a 4-tick pulse). Conversely, it suppresses any OFF-pulse shorter than its configured delay.
Signal Boosting, Diodes & Repeater Locking
Beyond simple delays, repeaters provide three structural properties essential to compact wiring:
- Signal Repeating: Redstone dust loses 1 power level for every block traveled from a maximum of 15. Placing a repeater restores the signal to 15. To maximize distance per repeater, place a solid opaque block directly before the repeater's back and another solid opaque block directly in front of its output—this achieves two extra blocks of reach compared to placing the repeater directly between dust lines.
- One-Way Diode: Because signals only enter the back and exit the front, repeaters prevent power from feeding backward into an input line and isolate parallel or sensitive sub-circuits.
- Signal Locking: When a powered repeater or powered redstone comparator faces directly into the left or right side of a repeater, that repeater becomes locked (
locked=true). A locked repeater freezes its current output state—staying ON if it was ON, or OFF if it was OFF—completely ignoring changes at its back input until the side power turns off. If a repeater is re-locked too quickly after unlocking, or if the lock and the input change on the exact same tick, the repeater will not switch states.
Common Circuits & Practical Tips
Repeaters are building blocks for timing, memory, and wire management:
- Multi-Repeater Delay Lines & Clocks: Chain multiple repeaters in series to create exact delays longer than 0.4 seconds (e.g., a 4-tick repeater followed by a 1-tick repeater yields a 0.5-second delay) or loop them to build adjustable repeater clocks.
- Data Latches (Memory Cells): Using the side-locking mechanic, a locked repeater acts as a memory cell, holding its output state until unlocked by a side repeater or comparator.
- Comparator-Controlled Locks: Because a comparator can lock a repeater from the side, you can lock or unlock a signal line based on container state or comparator inputs from three sides.
- Common Mistake — Pulse Loss in Fast Clocks: Running a 1-tick pulse into a 2-tick, 3-tick, or 4-tick repeater will stretch the ON-pulse and suppress any OFF-pulse shorter than the repeater's delay. Keep repeaters on 1-tick when transmitting 1-tick pulses.
Java vs Bedrock
| Topic | Java Edition | Bedrock Edition |
|---|---|---|
| First Repeater Delay Behavior | Every repeater adds at least 1 redstone tick (2 game ticks / 0.1s) of delay to a signal. | The first repeater can have a delay of zero, even though the repeater visually displays a 1-tick setting. |
