Item Despawn Wireless Redstone

Wireless redstone allows two machines to communicate across unlimited distances within the same dimension without any physical wiring between them. Discovered by 2No2Name and formalized by cubicmetre, this circuit exploits global item entity creation counters and sub-tick tile priority to transmit signals instantly across your world. It is ideal for remote ender pearl stasis chambers, long-distance base triggers, and multi-channel telemetry.

Signal TransmissionExpertJava Edition
Item Despawn Wireless Redstone video tutorial

Video: The Wonderful World of Wireless Redstone by cubicmetre

How to build it

  1. Build the Overworld Sync Clock

    At both your transmitter and receiver locations, place a Daylight Detector observed by an Observer. Because daylight detectors update in the exact same game tick everywhere in the Overworld, this acts as a global synchronization pulse.

  2. Construct the Receiver Dropper Traps

    At the receiver, place two Hoppers pointing down or back into two vertical or facing Droppers to form an item recycler. Place an Iron Trapdoor directly inside the space above each hopper so items dispensed onto the trapdoor sit on top until the trapdoor opens.

  3. Wire the Receiver Tile Sets

    Create two parallel delay lines (tile sets) leading from your sync clock into the two receiver droppers. Both lines must have the exact same total game-tick delay, but use different repeater delay combinations (for example, a 4-tick then 2-tick repeater on line A, and a 2-tick then 4-tick repeater on line B) so one dropper always fires before the other within the same tick.

  4. Add the Receiver Trapdoor Trigger

    Branch a short delay line from the receiver's sync clock to power both Iron Trapdoors simultaneously right after the droppers dispense their items. Load stackable items into both receiver droppers.

  5. Build the Phase Comparator Output

    Place a Redstone Comparator reading each of the two receiver hoppers. Wire their outputs into a logic gate (such as an AND/coincidence detector) connected to a Redstone Lamp so the lamp only triggers when both items fall into the hoppers on the exact same game tick.

  6. Set Up the Transmitter Tile Set

    At your remote transmitter location, run a line from its synced Daylight Detector into a chain of Redstone Repeaters. Set the repeater delays so that the total delay equals the receiver's total delay, but its tile-tick priority falls strictly between the receiver's first and second tile sets.

  7. Place the Transmitter Filler Droppers

    At the end of the transmitter's tile set, run the signal into a line of 3 Powered Rails with Observers powering 3 Droppers loaded with filler items. Point these droppers directly into hoppers to recycle the items.

  8. Add the Transmit Control Input

    Attach a Button or toggleable gate between the transmitter's sync clock and its tile set. When you press the button on a sync cycle, the transmitter fires 3 filler items in between the receiver's two items, shifting the second receiver item by 3 phases so both receiver items fall on the same game tick and light the lamp.

How it works

This wireless redstone system relies on two core Java Edition engine mechanics: tile tick priority and item entity modulo-4 falling phases.

  • Tile Tick Priority (Tile Sets): When multiple redstone components are scheduled to update in the exact same game tick, Minecraft processes them in a deterministic order. Repeaters are always processed before comparators, and repeaters scheduled earlier (with a longer delay setting) are processed before repeaters scheduled later (with a shorter delay setting), even if their total path delay is identical. By chaining different combinations of repeater delays (e.g., 4gt + 2gt vs 2gt + 4gt), you create unique tile sets that execute in a strict sub-tick order anywhere in the dimension.
  • Modulo-4 Item Falling: To optimize performance, dropped item entities sitting on a block only check if the block beneath them has been removed once every 4 game ticks. Each new item entity created in the world increments a global counter, assigning the item to one of 4 falling phases (0, 1, 2, or 3). Every fourth item created checks for falling on the exact same game tick.
  • The Transmission Protocol: During idle operation, the receiver dispenses two items onto closed trapdoors in the same game tick—one using an early-priority tile set and one using a late-priority tile set. Because they are created consecutively, they land in adjacent phases (e.g., Phase 0 and Phase 1). When the trapdoors open together, the two items start falling on different game ticks, and the receiver comparators see them at different times.
  • Shifting the Phase: When you activate the transmitter in that same game tick, its mid-priority tile set schedules 3 filler droppers to fire after the receiver's first dropper but before the receiver's second dropper. Creating 3 filler item entities shifts the second receiver item forward by 3 phases (from Phase 1 to Phase 4, which wraps around modulo 4 to Phase 0). Now both measured items in the receiver share the exact same phase, begin falling in the exact same game tick when the trapdoors open, and enter the hoppers simultaneously to trigger the output.

Tips & variations

  • Java Edition Exclusive: This mechanic depends on Java Edition's deterministic tile-tick list and global entity ID counter. It does not work on Bedrock Edition.
  • Cross-Dimension & Underground Sync: Daylight detectors only work in the Overworld with sky access. For the Nether, End, or deep underground builds, use a self-synchronizing clock (one module runs a 32-gt clock while the other runs a 31-gt clock until their measured phases coincide, locking both into a 32-gt cycle).
  • Chunk Loading: Both the transmitter and the receiver must be in entity-processing loaded chunks at the moment of transmission so the droppers can create item entities.
  • Multi-Receiver Protocols: The basic 2-item receiver protocol only supports a single receiver per frequency because a second receiver adds extra item entities that shift the phase. To use multiple receivers on the same network, use a binary-encoded reference channel protocol where filler items are compensated across all bit channels.
  • Avoid Unintended Item Spawns: Other contraptions dispensing items in the exact same sub-tick window can interfere with the phase offset. Schedule your tile sets cleanly and keep the recycler hoppers clogged-free.

Frequently asked questions

Does item entity wireless redstone have a distance limit?
No. As long as both the transmitter and receiver are in the same dimension and inside loaded chunks, the global item entity counter links them across any distance.
Why do my receiver items fall on different ticks when I press the button?
Check your tile set delays and repeater ordering. The transmitter's total game-tick delay from the daylight detector must match the receiver's total delay, and its repeater priority must sit strictly between the receiver's first and second dropper lines.
Can I add a second receiver on the same channel?
Not with the basic 2-item protocol, because a second receiver dispenses two extra items every cycle and shifts the modulo-4 phase. To run multiple receivers on one network, you must use a reference-channel binary protocol or assign each receiver its own unique tile-set network.

Components used

More wireless / sculk transmission