Rising Edge Detector

A rising edge detector (also called a monostable circuit) converts a long or continuous redstone signal into a short pulse the moment the input turns on. These circuits are essential for 3x3 and 4x4 piston doors, allowing sticky pistons to spit out their blocks on a 1-tick pulse, or for shortening a long button press.

Pulse CircuitsBeginnerJava Edition
Rising Edge Detector video tutorial

Video: Redstone Basics: Rising Edge Detectors by The Crusherhero

How to build it

  1. Build the Classic Block-Breaker (Design 1)

    Dig a 1-block hole and place a sticky piston facing upward inside it, then place a solid building block on top of the piston. Place your input redstone dust leading into the piston and a 1-tick redstone repeater running right through the solid block.

  2. Connect the Output

    Place a second piece of redstone dust directly in front of the block to receive the pulse from the repeater. When you trigger your button or lever, the repeater sends a 1-tick pulse before the piston pushes the block up and cuts the connection.

  3. Build the Multi-Directional Observer Detector (Design 2)

    Place a sticky piston facing in any direction you choose (up, down, or sideways) and attach an observer to its head, or place the observer so its face watches the piston move. Run your input into the piston and place redstone dust at the observer's output to collect the 1-tick pulse.

  4. Build the Wire-Cutter Detector (Design 3)

    Route a line of redstone dust down into a step and back up, then position a piston above the lower dust so that extending a block cuts the diagonal wire connection. Power both the redstone line and the piston from the same button input so the piston severs the signal after 1 to 1.5 ticks.

  5. Build the Dropper-Hopper Detector (Design 4)

    Place a dropper facing directly into a hopper, and aim the hopper right back into the dropper, then put a single item inside the dropper. Place a redstone comparator reading from the hopper; pressing a button on the dropper shoots the item into the hopper to create a slightly longer 3.5-tick pulse before it returns.

  6. Build the Subtraction Comparator Detector (Design 5)

    Place a redstone comparator and right-click it to turn on subtraction mode (front torch lit), then feed your input into the back through a repeater. Split the output from the front block so a side line of redstone dust (and optional delay repeaters) loops into the comparator's side input to subtract signal strength 14 from 15 and cut off the pulse.

  7. Build the Torch and Repeater Gate (Design 6)

    Using only 5 redstone dust, 2 redstone torches, and 1 delayed repeater, split your input into two paths: a direct path and a delayed repeater path. Combine them with redstone torches so the output torch only flashes on during the brief moment when the current power and previous delayed power differ.

  8. Build the Locked Repeater Detector (Design 7)

    Place an output repeater and run a second repeater into its side, powered by a redstone torch on a block so the output repeater starts locked. Wire your button input to both turn off the redstone torch and power the main repeater, allowing a 1-tick pulse to escape before the repeater locks again.

How it works

A rising edge detector works by racing two versions of the same input signal against each other: a fast path that turns the output ON immediately, and a slightly delayed path that cuts the output OFF right after.

  • Piston Cut-Off (Designs 1 & 3): Electricity travels through a solid block or diagonal wire immediately, while a piston powered at the same moment takes 1 redstone tick to start extending. Once the block moves, the circuit breaks, leaving only a 1-tick pulse at the output ( enabling sticky pistons in Java Edition to spit out their blocks).
  • Observer Update (Design 2): An observer watches a piston change state and emits a crisp 1-tick redstone pulse whenever the piston extends.
  • Item Transfer (Design 4): A dropper pushes an item into a hopper when powered. The comparator detects the item in the hopper for roughly 3.5 ticks until the hopper pushes the item back into the dropper.
  • Logic & Subtraction (Designs 5, 6 & 7): Using comparator subtraction, torch inverters, or locked repeaters, the initial signal passes through while a secondary delayed branch cancels, subtracts, or re-locks the output line.

Tips & variations

  • Java vs. Bedrock Note: These circuits were built and tested in Minecraft Java Edition. The 1-tick sticky piston block-spitting mechanic (used heavily in 3x3 and 4x4 piston doors) is a Java-exclusive feature and will not leave the block behind in Bedrock Edition.
  • Adjusting Pulse Length: If a 1-tick pulse is too short for your mechanism (for example, opening a trapdoor briefly), use the Dropper-Hopper design for a 3.5-tick pulse, or add extra delay to the repeaters in the Subtraction Comparator design.
  • Going Vertical: The Observer design is the most flexible when building in tight spaces because pistons and observers can be aimed straight up, straight down, or sideways.
  • Survival Friendly: If you do not have slimeballs or Nether quartz early in survival, use the Torch and Repeater Gate (Design 6) or the Locked Repeater (Design 7), which only require redstone dust, repeaters, and torches.

Frequently asked questions

What does a rising edge detector do in Minecraft?
It detects the exact moment a redstone signal turns from off to on (the rising edge) and outputs a brief pulse, regardless of how long the input stays powered.
Why does my sticky piston leave its block behind?
In Minecraft Java Edition, when a sticky piston receives a 1-tick pulse from a rising edge detector, it pushes its block out and retracts immediately without pulling the block back. Pressing the input a second time will retrieve the block.
Which rising edge detector is best for a 3x3 piston door?
The classic sticky piston with a block and repeater (Design 1) or the observer detector (Design 2) are the most popular for 3x3 and 4x4 piston doors because they reliably output a 1-tick pulse to spit out the center door blocks.

Components used

More edge detector