Rising and Falling Edge Monostable Circuits

A monostable circuit converts a sustained or long redstone input—such as a flipped lever or comparator output—into a single, brief pulse. This guide covers both rising edge circuits (which fire the moment an input turns on) and falling edge circuits (which fire the moment an input turns off). They are essential building blocks for 3x3 piston doors and other contraptions that require precise timing rather than a continuous signal.

Pulse CircuitsBeginnerBedrock Edition
Rising and Falling Edge Monostable Circuits video tutorial

Video: Understanding Monostable Circuits | NoobStone | Minecraft Bedrock Edition 1.20 Redstone Tutorial by NoobCraft

How to build it

  1. Rising Edge: Set Up the Piston and Block

    Dig a one-block hole and place a regular piston inside facing straight up. Place a gravity block like gravel or sand directly on top of the piston face so it sits at ground level.

  2. Rising Edge: Connect the Input

    Place a piece of redstone dust on the ground directly behind the gravity block. Attach your input source, such as a lever, next to the dust so it can power both the block and the piston below it.

  3. Rising Edge: Add the Output Repeater

    On the opposite side of the gravity block, place a redstone repeater facing away from the block. Connect the repeater to a redstone lamp or your output line to finish the rising edge circuit.

  4. Falling Edge: Build an Inverter Input

    For the falling edge design, start with a solid input block that has a lever on one side and a redstone torch attached to the output side. Turning the lever on will keep this torch turned off.

  5. Falling Edge: Attach a Sticky Piston and Redstone Block

    Place a sticky piston next to the redstone torch so the torch powers it when lit. Attach a block of redstone to the face of the sticky piston.

  6. Falling Edge: Build the Breaker Assembly

    Place a piece of redstone dust where the block of redstone will land when extended. Next to that dust, dig a one-block hole for an upward-facing regular piston with a gravel block on top.

  7. Falling Edge: Connect the Final Output

    Place a redstone repeater facing out from the gravel block and run it into your output lamp. Flip the input lever on, then turn it off to trigger a single falling-edge pulse.

How it works

Both circuits work as "circuit breakers" that allow a signal to pass through a conductive block right before a piston moves that block out of the way.

  • Rising Edge: When the input turns on, the redstone dust powers the gravity block and simultaneously activates the piston underneath it. The redstone repeater pulls a brief pulse through the gravity block in the split second before the piston pushes the block upward, cutting off the connection. When the input turns off, the block drops back into place without firing the repeater.
  • Falling Edge: The redstone torch inverts the input, staying off while the lever is on. When you turn the lever off, the torch turns back on and extends the sticky piston, pushing the Block of Redstone next to the redstone dust. Just like the rising edge design, the dust powers the gravity block long enough for the repeater to emit a single pulse before the lower piston pushes the block up and breaks the line.

Tips & variations

  • Sticky Piston Alternative: If you do not want to use a regular piston with a gravity block like sand or gravel, you can substitute an upward-facing sticky piston and any solid conductive block of your choice.
  • Why the Falling Edge Needs a Redstone Block: In Bedrock Edition, you cannot simply place a redstone torch directly behind the gravity-block breaker. The torch inversion delay causes the lower piston to extend before the repeater can pull a signal through the block. Using a sticky piston to push a block of redstone eliminates this timing mismatch and guarantees the pulse gets through.

Frequently asked questions

What is the difference between a rising edge and a falling edge monostable circuit?
A rising edge circuit sends a short output pulse at the very beginning of an input signal (when it turns ON), while a falling edge circuit sends its pulse at the end of an input signal (when it turns OFF).
Can I use a solid block instead of gravel or sand?
Yes. If you replace the regular upward-facing piston with a sticky piston, you can use any solid conductive building block instead of a gravity block.
Why doesn't the falling edge circuit work if I wire the redstone torch directly into the dust?
In Minecraft Bedrock, the delay from the redstone torch causes the upward piston to push the block out of the way before the repeater has time to power on. Pushing a redstone block with a sticky piston fixes this timing issue.

Components used

More edge detector