Silent Rising and Falling Edge Detectors

Edge detectors, also known as monostable circuits or pulse limiters, convert long or sustained redstone signals into a quick 1-tick pulse. This tutorial covers two completely silent, pistonless designs: a 2x2x3 falling edge detector that fires when a signal turns off, and a 1-wide (1x2x4) rising edge detector that triggers the moment a signal turns on. They are ideal for survival contraptions where you want to avoid noisy pistons and expensive quartz components.

Pulse CircuitsBeginnerJava Edition
Silent Rising and Falling Edge Detectors video tutorial

Video: Silent Compact 1-Tick Pulse Generators - Rising and Falling Edge Detectors - Redstone Tutorial by JustPanda

How to build it

  1. Falling Edge Detector: Input & Double Inverter

    Start the 2x2x3 falling edge design by placing a solid input block with a button or lever attached. Place a redstone torch on the side of the input block, run redstone dust from that torch into a second solid block, and attach a second redstone torch to that block to invert the signal twice.

  2. Falling Edge Detector: Repeater Lock Setup

    In the 2-wide space next to your torches, place an output redstone repeater receiving power from the second torch. Place a second repeater facing directly into the side of the output repeater to act as a lock.

  3. Falling Edge Detector: Connect the Top Line

    Place a piece of redstone dust on top of the input block arrangement so it powers the locking repeater as soon as the input is activated. Place a redstone lamp or your output line in front of the main output repeater to test the 1-tick pulse when the button turns off.

  4. Rising Edge Detector: Input & Bottom Repeater

    For the 1x2x4 rising edge design, place a floating input block one block above the ground with a button or lever on the front. Place a single piece of redstone dust directly underneath this input block.

  5. Rising Edge Detector: 3-Tick Delay & Output Torch

    Running straight back from the bottom redstone dust, place a redstone repeater and right-click it twice to set it to a 3-tick delay. Have this repeater run directly into a second solid block, and attach a redstone torch to the far side of that second block as your output.

  6. Rising Edge Detector: Top Torch Override

    Attach a redstone torch to the back of the first input block (sitting right above the repeater). Finally, place a piece of redstone dust on top of the second solid block so that the top torch normally keeps the bottom output torch turned off.

How it works

Both circuits rely on exact redstone tick timings between redstone torches (which take 1 redstone tick to change state) and repeaters rather than moving blocks:

  • Falling Edge Detector (2x2x3): Using two redstone torches in series inverts the signal twice while introducing a 2-tick delay. When you press the button or flip the lever on, the locking repeater powers after 1 tick and locks the output repeater. When the input finally turns off, the locking repeater unpowers after 1 tick, while the double-torch line takes 2 ticks to turn off. That 1-tick difference allows a single 1-tick pulse to escape through the output repeater at the very end of the signal.
  • Rising Edge Detector (1x2x4): In its resting state, the torch on the back of the input block powers the redstone dust on the second block, holding the final output torch off. When the input turns on, the top torch turns off after 1 tick, freeing the output torch to turn on. At the same time, the bottom repeater delays the incoming on-signal by 3 ticks. Once that 3-tick signal reaches the second block, it forces the output torch back off—resulting in a clean 1-tick pulse at the start of the signal.

Tips & variations

  • Cheap Survival Alternative: In the falling edge detector, using two redstone torches for a 2-tick delay uses only sticks and redstone dust, making it slightly cheaper in early survival than crafting an extra repeater.
  • Works with Solid Signals: Neither design requires a button. You can hook a lever, pressure plate, or long comparator readout to either circuit; the rising edge design will pulse as soon as the lever is flicked on, and the falling edge design will pulse as soon as the lever is flicked off.
  • Common Mistake: Make sure the repeater in the 1-wide rising edge detector is set to 3 ticks (two right-clicks). If left on 1 or 2 ticks, the bottom line will power the second block before the output torch has time to turn on.

Frequently asked questions

What is the difference between a rising edge and a falling edge detector?
A rising edge detector emits a short pulse the moment an input signal turns ON, whereas a falling edge detector waits and emits a pulse the moment the input signal turns OFF.
Can I use a lever instead of a button on these pulse generators?
Yes. Both circuits convert sustained signals from a lever into a single 1-tick pulse—one when you flick the lever on, and the other when you flick the lever off.
Why are these edge detectors completely silent?
Unlike sticky-piston monostable circuits or dropper-hopper pulse limiters, these designs rely entirely on redstone torch burnout/inversion delays and repeater locking, which make no sound in-game.

Components used

More edge detector