Bedrock Edge Detectors

An edge detector (or monostable circuit) converts a long, continuous redstone signal into a single short pulse. Rising edge detectors output a pulse the moment a signal turns on, while falling edge detectors fire only when the signal turns completely off. These circuits are essential for item sorters, farm automation, and timing mechanisms where you need to know exactly when a process starts or finishes.

Pulse CircuitsBeginnerBedrock Edition
Bedrock Edge Detectors video tutorial

Video: How do edge detectors work? Minecraft Bedrock Edition by MaddHatter

How to build it

  1. Rising Edge 1: Vertical Piston Breaker

    Run your input redstone dust into the side of a upward-facing sticky piston with a solid block on its head (or a normal piston with sand). Place a repeater pointing into the side of that pushed block and another repeater coming out the opposite side; when the input turns on, the repeater briefly powers the block before the piston pushes it out of the way.

  2. Rising Edge 2: Inverting Torch Tower

    Build a vertical or diagonal tower of blocks using three redstone torches arranged so that the input turns off two torches simultaneously while the third torch adds a 1-tick delay. Because the final torch reacts one tick slower than the parallel path, a brief 1-tick pulse escapes to the output at the top.

  3. Rising Edge 3: Sticky Piston & Observer

    Attach an observer to a sticky piston so the piston pushes the observer toward an output block. When powered, the observer fires a pulse as it moves into position, while the retraction pulse fires harmlessly before it reaches the output block.

  4. Rising Edge 4: Flat Torch Inverter

    To build the torch tower horizontally, power an input block that splits a redstone dust line into two paths. Send one path straight forward and the other through a 2-tick repeater into a block with a redstone torch on the end to create a flat rising-edge pulse.

  5. Rising Edge 5: Subtract Mode Comparator

    Place a redstone comparator and click it to turn on the front torch (subtract mode). Split your input so it runs directly into the rear of the comparator and also through a 2-tick repeater into the side of the comparator; when turned on, it outputs a brief pulse before the side input subtracts 15 and shuts it off.

  6. Falling Edge 1: Locked Repeater Circuit

    Split your input line so one branch runs directly into the side of a repeater to lock it, and the other branch runs through a delayed repeater into the back of that locked repeater. While the input is on, the output stays locked off; when the input turns off, the side lock releases first while the delayed rear repeater briefly pushes a pulse through.

  7. Falling Edge 2: Piston Return Breaker

    Build the same upward-facing piston setup from Rising Edge 1, but align your input and output repeaters with the block's extended position or adjust the signal timing. This allows the circuit to pulse on the return movement, or even detect both rising and falling edges from the same piston.

  8. Falling Edge 3: Universal Comparator Subtractor

    Place a comparator in subtract mode and put a repeater on both the rear input line and the side subtraction line. Set the rear repeater to a longer delay than the side repeater for a falling edge pulse, or swap the repeater delays to turn the exact same footprint into a rising edge detector.

  9. Falling Edge 4: Bedrock Observer-Torch Detector

    Chain two observers together looking at your input line, leading into a solid block that has a redstone torch on it, and run a parallel repeater from the input into that same block. The repeater prevents a feedback loop and keeps the block powered while the input is on, so the observer-triggered torch only blinks on when the signal turns off.

How it works

Edge detectors rely on race conditions—splitting a single redstone signal into two paths with slightly different delays so they cancel each other out after a couple of ticks.

  • Rising Edge (On-Pulse): The fast path immediately turns the output ON, while the slower path arrives 1 to 2 ticks later to cut the signal off (either by moving a block with a piston, inverting a redstone torch, or subtracting signal strength of 15 via a comparator).
  • Falling Edge (Off-Pulse): While the main input is active, the output is held off by a locked repeater, a subtract comparator, or a powered torch block. The moment the main input turns OFF, the blocking mechanism releases first while a delayed path still holds power for a brief tick, letting a short pulse escape.

Tips & variations

  • Silent vs. Noisy: Piston-based edge detectors are compact and can detect both edges, but they make piston sounds every cycle. Use the torch or comparator variants for completely silent builds.
  • Reversible Comparator Trick: The dual-repeater comparator subtractor is the easiest design to memorize—just change which repeater has more ticks of delay to switch between rising edge and falling edge on the fly.
  • Java vs. Bedrock Note: Most torch, repeater-lock, and comparator designs work across editions, but the final observer-into-torch falling edge circuit relies on Bedrock-specific observer and torch timing and will not work on Java Edition.

Frequently asked questions

What is the difference between a rising edge and a falling edge detector?
A rising edge detector outputs a short pulse the moment a redstone signal turns on. A falling edge detector waits and outputs a short pulse only when the redstone signal turns off.
When should I use a falling edge detector in survival?
Falling edge detectors are great for item sorting and furnace arrays where an active stream of items keeps a circuit powered, and you want to trigger an action only after the items completely stop flowing.
Which edge detector is the easiest to configure?
The comparator subtract circuit with two repeaters is the most versatile because you can switch it between rising edge and falling edge simply by changing which repeater has the longer tick delay.

Components used

More edge detector