Pulse Extender Designs

A redstone pulse extender takes a short input—like a quick button press—and holds the signal on for a longer period of time. These circuits are essential for keeping piston doors open long enough to walk through, running farm collection cycles, or timing automated machines. Below are five different designs ranging from ultra-simple repeater delays to multi-minute hopper timers.

Pulse CircuitsBeginnerJava Edition
Pulse Extender Designs video tutorial

Video: [UPDATED] The Best Redstone Signal Pulse Extenders that YOU SHOULD KNOW! by Dusty Dude

How to build it

  1. Design 1: Simple Dual-Path Repeater Extender

    Place your input button with a short line of redstone dust leading into two parallel branches. On the main branch, place a 1-tick repeater leading into two redstone dust and your output lamp. On the parallel branch, place two 4-tick repeaters feeding into a solid block next to the output dust to keep the lamp powered longer.

  2. Design 2: Expandable Repeater Line

    Place a solid block with an input button on it. Coming out of that block, alternate solid blocks and 4-tick redstone repeaters in a straight line for as long as you want the delay to last, ending on a solid block.

  3. Design 2: Connect the Output Line

    Run a continuous line of redstone dust directly alongside all of the solid blocks and repeaters you just placed, leading into your output block and redstone lamp.

  4. Design 3: Vertical Comparator Fader Base

    Place an input button feeding into a repeater that powers a solid block. From that block, place solid blocks in an alternating staggered pattern (one low, one high) and place redstone dust on the exposed end blocks.

  5. Design 3: Add Comparators and Top Dust

    Place redstone comparators on the lower level facing backward toward the input, and comparators on the upper level facing forward away from the input. Run redstone dust across the top blocks and take your output from the first top block for zero initial delay.

  6. Design 4: Compact Hopper Extender Base

    Place an input block with a button on one side and a redstone torch on the opposite side. Place two hoppers on the ground facing directly into each other so items can transfer back and forth.

  7. Design 4: Comparator and Torch Output

    Have a comparator read from one hopper and point back into the input block, with a line of redstone dust climbing up the side to lock the hopper. Place a second redstone torch on the side of the block to power your output line, then add items inside the hopper to set the duration.

  8. Design 5: Modified Etho Hopper Extender Base

    Place two hoppers facing into each other in the center. On both ends of the hoppers, place a comparator facing outward into a raised solid block, and place a piece of redstone dust on top of each end block.

  9. Design 5: Pistons and Redstone Block

    Against the end blocks, place one sticky piston on one side and one regular (non-sticky) piston on the other side, both facing inward toward the hoppers. Place a block of redstone between the pistons and put your desired number of items into the hoppers.

  10. Design 5: Input and Output Setup

    Place your input button on the end block behind the regular piston. Take your output using a repeater reading from the hopper line into your output lamp.

How it works

Each of these five designs extends a pulse using a different redstone mechanic:

  • Designs 1 & 2 (Repeater Delays): The initial button pulse travels down a fast redstone dust line to turn the output on immediately, while also entering a chain of 4-tick repeaters. As the signal ripples through the repeaters and solid blocks, it continuously re-powers the adjacent output dust line until the last repeater turns off.
  • Design 3 (Comparator Decay Loop): A repeater injects signal strength 15 into a loop of comparators. Because comparators preserve signal strength while redstone dust at the ends drops the strength by 1 per loop cycle, the signal slowly fades out down to 0, keeping the output powered the entire time.
  • Design 4 (Torch & Hopper Timer): In its resting state, one hopper is locked while the other holds items. Pressing the button flips the torch state briefly, allowing items to flow into the second hopper. The comparator reads those items and holds the circuit active until every item has transferred back,though it requires a brief reset recovery period after turning off.
  • Design 5 (Modified Etho Hopper Clock): By replacing one of the sticky pistons in a standard Etho hopper clock with a regular piston, the clock only runs for a single full cycle when triggered. Pressing the button pushes the redstone block to unlock the first hopper; once all items transfer, the opposite piston pushes the redstone block back and the circuit stops immediately with zero reset cooldown.

Tips & variations

  • Choosing the right extender: Use the repeater or comparator fader designs for short delays (1 to 10 seconds), and the hopper designs for long delays (up to several minutes).
  • Avoiding cooldown issues: Design 4 (the single-torch hopper extender) has a reset phase after the light turns off while items move back to the starting hopper. Triggering it again too early will result in a shorter second pulse. Use Design 5 (the modified Etho hopper extender) if you need the circuit to be ready immediately after the output turns off.
  • Adjusting hopper timing: You can put up to 5 stacks of any item inside the modified Etho hopper extender. Each item adds roughly 0.8 seconds to the total round-trip pulse duration.

Frequently asked questions

Which pulse extender is best for very long delays?
The modified Etho hopper extender (Design 5) is best for long delays because it can hold up to 5 stacks of items and stays active while the items transfer both ways.
Why does the modified Etho hopper extender use one sticky piston and one regular piston?
Using one regular piston and one sticky piston stops the hopper clock from looping forever. Once the items finish moving one way and then return to the starting hopper, the circuit stops and waits for the next button press.
Why is my compact hopper pulse extender giving a shorter pulse the second time I press the button?
Design 4 has a reset phase where items must finish returning to the first hopper after the output turns off. If you need no cooldown between presses, use Design 5 instead.

Components used

More pulse extender