Simple Pulse Extenders

A redstone pulse extender takes a brief input signal—like the quick flick of an observer or a button press—and holds the output active for a longer, controlled duration. These circuits are essential for keeping piston doors open long enough to walk through, running automated tree farms, or timing complex vault doors. This guide covers four different pulse extender styles ranging from less than a second up to five full minutes.

Pulse CircuitsBeginnerJava Edition
Simple Pulse Extenders video tutorial

Video: SIMPLE pulse extenders for Minecraft 1.20 by Gecko

How to build it

  1. Basic Comparator Fader Loop (0.6s to 1.6s)

    For a quick pulse extender, place a redstone comparator facing forward and a parallel line of redstone dust beside it, connected at both ends with two more dust to form a 2x3 loop. For a 1.6-second pulse (32 game ticks), replace that side dust with a second comparator facing the opposite direction so both comparators feed into each other via two dust at each end.

  2. Extended Comparator Chains (3.2s to 12s)

    To make the comparator loop last longer, extend the two parallel lines by adding more comparators facing opposite directions in a loop. When using four total comparators (two on each side, lasting 3.2 seconds), replace one corner redstone dust with a repeater set to 4 ticks so the signal has enough delay to travel through the chain, and use a stone button (up to 8s) or wooden button (up to 12s) as the input for larger loops.

  3. Adjustable Hopper Extender: Input & Pistons

    For a customizable long pulse (up to 4.25 minutes), place a building block with a button on it and redstone dust on top. Next to the dust, place a sticky piston facing sideways with a Block of Redstone attached to its face.

  4. Adjustable Hopper Extender: Hoppers & Comparators

    Place two hoppers facing directly into each other so items can transfer back and forth adjacent to the redstone block's positions. Have a comparator read out of each hopper in opposite outward directions, running each comparator into a solid block with a piece of redstone dust next to it.

  5. Adjustable Hopper Extender: Output & Items

    Place a regular piston facing the Block of Redstone on the opposite side of the sticky piston so it gets powered when the second hopper finishes filling. Add your desired number of items into the first hopper (use the formula 16N - 14 = game ticks, where N is the item count) and take your extended redstone output from one of the hopper comparators.

  6. 5-Minute Item Despawn Extender

    Place a wooden pressure plate on the ground and surround its four sides with solid blocks to form a small containment tube. One block above the pressure plate, place a horizontal chain inside the tube with a dropper facing directly into the chain, and surround the top layer with blocks so ejected items align straight down onto the plate.

  7. Fill Dropper and Connect Output

    Fill the dropper with any spare stackable items and place a button on the dropper to trigger it. Run redstone dust from the block beneath or adjacent to the wooden pressure plate to your output device; the signal will stay active for 5 minutes until the item despawns.

  8. 1-Minute Arrow Despawn Extender

    For a compact 1-minute pulse (1,230 game ticks), place a wooden pressure plate on the ground and position a dispenser facing directly into the space above it. Load the dispenser with arrows and attach a button; firing an arrow onto the wooden pressure plate holds the output on until the arrow despawns after roughly 61.5 seconds.

How it works

Each of these pulse extenders uses a different redstone mechanic to hold a signal active after the initial input turns off:

  • Comparator Fader Loop: When a signal of strength 15 enters the loop, the comparator outputs strength 15 into the adjacent redstone dust. Because two pieces of dust connect the ends of the loop, the signal drops by 1 each time it cycles through (15, 14, 13, down to 0). Adding more comparators increases the delay of each cycle.
  • Hopper-Piston Extender: Pressing the button powers the sticky piston, pulling the Block of Redstone to the other hopper. This unlocks the first hopper so items transfer one by one into the second hopper while locking the second hopper. Once the first hopper empties, the regular piston pushes the redstone block back, resetting the circuit once the items return.
  • Despawn Extenders: Wooden pressure plates detect entities resting on them. A dropped item entity remains in the world for 6,000 game ticks (5 minutes), while a fired arrow entity despawns after 1,200 game ticks (1 minute). As soon as the entity despawns, the plate pops back up and cuts the signal.

Tips & variations

  • Button Timings Matter: A stone button naturally stays active for 1 second (20 game ticks / 10 redstone ticks), while a wooden button stays on for 1.5 seconds (30 game ticks / 15 redstone ticks). Always factor in input duration when calculating total pulse length.
  • Preventing Infinite Clocks: On long comparator loops (8 to 12 seconds), do not use an observer as the input; the 1-tick pulse is shorter than the loop traversal time and will turn the extender into an endless blinking clock. Use a stone or wooden button instead.
  • Hopper Item Formula: For 4 or more items in the hopper extender, calculate exact duration in game ticks using 16N - 14 = G (where N is the item count). Divide G by 20 to get the time in seconds. For 1, 2, or 3 items, the pulse lasts 1.3s, 1.35s, and 1.75s respectively.
  • Use Wooden Pressure Plates: Stone pressure plates cannot detect dropped items or fired arrows—you must use a wooden pressure plate for the despawn designs.

Frequently asked questions

What is the difference between a stone button and a wooden button in redstone?
A stone button outputs a pulse for 1 second (10 redstone ticks or 20 game ticks), whereas a wooden button lasts 1.5 seconds (15 redstone ticks or 30 game ticks).
Why did my long comparator pulse extender turn into a flashing clock?
Your input pulse was shorter than the time it takes the signal to travel through all the comparators in the loop. Switch from an observer input to a stone or wooden button so the entire loop fills to signal strength 15 before decaying.
How long can the hopper pulse extender hold a signal?
By filling all five slots of the hopper with full stacks of 64 items (320 items total), the hopper pulse extender can hold a signal active for up to 4.25 minutes.
Why isn't the arrow or item despawn extender powering my redstone?
Make sure you are using a wooden pressure plate. Stone and polished blackstone pressure plates only respond to players and mobs, not dropped items or arrows.

Components used

More pulse extender