Comparator Pulse Extender

A comparator pulse extender takes a brief redstone signal—like the press of a button—and holds the output active for a longer duration before turning off. While the classic comparator fader loop sits flat and takes up a two-block-wide footprint, this vertical design rearranges the loop into a 1-wide slice. It is ideal for tight redstone builds where horizontal space is limited and you need flexible input and output placements.

Pulse CircuitsBeginnerJava Edition
Comparator Pulse Extender video tutorial

Video: Minecraft: Comparator Pulse Extender Tutorial (Redstone Advent Calendar) by xisumavoid

How to build it

  1. Place the Two-Dust Decay Base

    Start by placing two solid building blocks next to each other in a 1-wide line and put a piece of redstone dust on top of both. These two adjacent dust pieces are where the signal strength drops by one each time it loops around.

  2. Add the Lower Comparators

    Place a comparator pointing directly into the two-dust line, and place a solid block directly behind that comparator. Add a second comparator on the lower level so the signal can travel in a vertical circle.

  3. Close the 3-Comparator Loop

    Place a third comparator on the upper level pointing in the opposite direction of the bottom comparator to complete the circular path. Place a solid block above the end of the loop with a piece of redstone dust to bridge the signal back into the circuit.

  4. Expand to an Even Number of Comparators

    If you want a longer pulse using four comparators (or any even count), add another comparator to the vertical loop and place a solid block in front of it. Put a block above and a piece of redstone dust on the block below it to transfer the signal downward into the return line.

  5. Expand to an Odd Number of Comparators

    To extend the design to five comparators (or any odd count), make sure the top comparator faces the opposite direction to keep the loop flowing in one circle. Place the solid block and redstone dust at the end so the signal feeds cleanly into the next layer.

  6. Connect Your Input and Output

    Attach your input pulse (such as a button or lever) and your output line to any of the powered solid blocks along the top or sides of the loop, avoiding the bottom support blocks. Trigger the input to test the extended pulse decay.

How it works

This circuit works by adapting the classic horizontal comparator decay loop into a 1-wide vertical loop:

  • Signal Preservation: A Redstone Comparator passes along the exact signal strength it receives without losing power, adding 1 redstone tick (0.1 seconds) of delay per comparator.
  • Controlled Signal Decay: Most connections in the vertical loop pass through a single piece of Redstone Dust or a solid block, which preserves the current signal strength. However, the section with two adjacent pieces of redstone dust forces the signal strength to drop by 1 every time the pulse completes a full lap.
  • Loop Count vs. Duration: If you input a full strength-15 signal, it must travel around the loop 15 times before decaying to 0. A loop with 3 comparators delays each step by 3 redstone ticks, while expanding the loop to 4, 5, 6, or 7 comparators makes each lap take progressively longer.

Tips & variations

  • Not Tileable: Although the build is strictly 1-block wide, it is not directly tileable side-by-side because the exposed redstone dust on top will connect to neighboring slices and cross-power them. Leave a 1-block air gap or use solid blocks to isolate adjacent circuits.
  • Flexible I/O Placement: You do not need a fixed input or output port. Any of the powered blocks around the top and middle of the loop can accept an input pulse or power an output component, as long as you do not use the bottom-most base blocks underneath the comparators.
  • Common Mistake: When expanding the loop between odd and even numbers of comparators, double-check the arrow direction on every comparator. They must all follow a single continuous clockwise or counter-clockwise flow.

Frequently asked questions

Is this 1-wide comparator pulse extender tileable?
No. While it fits into a 1-block-wide gap, the redstone dust on top will connect to adjacent slices if placed right next to each other.
How do I make the pulse last longer?
Add more comparators to the vertical circle (for example, expanding from 3 comparators up to 4, 5, 6, or 7). More comparators mean each decay cycle takes longer to complete.
Where can I place the input and output?
You can power the circuit or take an output from almost any of the powered solid blocks along the sides or top of the loop, except for the bottom support blocks.

Components used

More pulse extender