Pulse Extender

A pulse extender takes a brief redstone signal—like the quick press of a button—and holds the output on for a much longer duration. These circuits are essential for keeping pistons retracted long enough to walk through secret doors, holding lighting systems active, or timing automated farms. Below, we cover four simple designs ranging from a few extra ticks to a full five-minute timer.

Pulse CircuitsBeginnerJava Edition
Pulse Extender video tutorial

Video: HI-LO Tech: Pulse Extenders by Mumbo Jumbo

How to build it

  1. Design 1: Repeater Loop Setup

    Place an input block with a button on it and an output block a couple of spaces away. Run a 1-tick redstone repeater directly from the input block into the output block.

  2. Complete the Repeater Loop

    Branch out from the input block with a loop of repeaters set to 4 ticks, using solid blocks at the corners to save on redstone dust. Feed the end of this repeater chain directly into the same output block so the delayed signal holds the output on after the button turns off.

  3. Design 2: Inline Repeater Extender

    For an even simpler repeater extender, place an input block with a button, a 4-tick repeater facing out of it, and another solid block in front of that repeater.

  4. Run Parallel Redstone Dust

    Lay a line of redstone dust alongside the blocks and the repeater, connecting the input to your output lamp. The dust turns the output on immediately, while the 4-tick repeater holds the line powered after the button pops out.

  5. Design 3: Compact Comparator Fader

    To build the compact comparator pulse extender, place two redstone comparators right next to each other facing in opposite directions.

  6. Link the Comparators with Dust

    Place two pieces of redstone dust at each end to connect the output of each comparator into the rear input of the other. Connect your button input to one end and your redstone lamp output to the other.

  7. Design 4: 5-Minute Despawn Timer Base

    For a 5-minute pulse, place a solid block with a dropper on top facing toward a 1x1 space. Place a wooden pressure plate on the floor directly in front of and below where the dropper will spit items, with your output redstone or lamp beside it.

  8. Enclose the Tube and Fill the Dropper

    Surround the space above the pressure plate with glass blocks to form a closed chute so items always land squarely on the plate. Fill the dropper with cheap disposable items and place a button on the block powering the dropper.

How it works

Each of the four pulse extenders uses a different redstone mechanic to keep the output powered after the initial button press ends:

  • Repeater Loop & Inline Repeaters: A fast path (either a 1-tick repeater or direct redstone dust) powers the output almost instantly. At the same time, the signal travels through one or more 4-tick repeaters. When the button turns off, the delayed信号 still moving through the repeaters continues feeding the output block until the final repeater powers down.
  • Comparator Fader Loop: Unlike repeaters, a redstone-comparator outputs the exact same signal strength that enters its rear. When a button powers the loop at full strength (15), the two pieces of redstone dust at the ends cause the signal to decay by 1 every time it passes from one comparator to the other (15, 14, 13, 12...) until it slowly reaches 0 and turns off.
  • 5-Minute Item Despawn Extender: Pressing the button triggers the dropper to eject a single item onto the wooden pressure plate. The plate immediately emits a continuous redstone signal and stays active until the dropped item naturally despawns after 5 minutes.

Tips & variations

  • Expanding the Inline Repeater Extender: You can chain multiple block-and-repeater pairs in a straight line alongside a single line of redstone dust, provided the dust line does not exceed the 15-block signal strength limit.
  • Expanding the Comparator Fader: For much longer delays without using items, add more pairs of comparators facing opposite directions in parallel before closing the loop with redstone dust at the ends.
  • Disposable Items Only: Never put valuable items inside the 5-minute dropper timer—its entire timing mechanic relies on the item permanently despawning.
  • Avoid Arrow Despawn Timers: While dispenser-shot arrows normally despawn after 1 minute and can press wooden buttons, arrow inaccuracy makes them miss the button frequently, and version bugs (such as in 1.7) can prevent arrows from despawning naturally.

Frequently asked questions

Which pulse extender is the most compact for medium delays?
The two-comparator fader loop is the most compact option for medium-to-long delays, taking up only a 2x3 footprint while holding a signal much longer than a couple of repeaters.
How do I make the comparator pulse extender last longer?
Simply lengthen the loop by placing additional comparators in a line facing one way and matching comparators next to them facing the return direction, then link the two ends with redstone dust.
Why doesn't the comparator loop turn into an infinite clock?
Because two pieces of redstone dust sit side-by-side at each turn of the loop, the signal strength drops by 1 every time it transfers from one dust piece to the next, eventually fading to zero.

Components used

More pulse extender