
Video: ReCategorizer: Tutorial + Download | Minecraft 1.19+/1.20+ by Maizuma Games
How to build it
- Set Up Chest Columns and Control Platform
Reserve a 3x12 area (ideally chunk-aligned) for the control circuit and place columns of double chests beside it (5 chests tall is recommended). Behind each chest column, place hoppers pointing into the chests, topped with a barrel and a downward-facing hopper.
- Build the Slice Valves
Behind the top barrel line of your categorized slices, place observers facing the back with rails along their front faces. Lead the observers into solid blocks and comparators, and place upward-facing droppers feeding into hoppers. Fill every slot of these valve droppers with 1 pair of shears (or non-stackable items) plus 1 extra inside the hopper so all comparators turn on.
- Build the Detection System
Behind the valves, place target blocks with redstone dust leading into comparators and upward-facing droppers with hoppers on top. Fill these detection containers completely, using 3 snowballs (16-stackable) and 4 shears per slice.
- Install Category Filter Chests
Place a double chest above each detection slice with hoppers feeding into and underneath it. Fill every slot of the filter double chest with filler items (like shears or renamed glass panes) that you will later swap for the specific items you want that slice to sort.
- Prime and Reset the Slices
Run a redstone dust reset line across slabs over the slices and attach a button. Press the button repeatedly until the top droppers empty out, every valve comparator turns on, the redstone dust behind the target blocks sits at signal strength 1, and the top filter hoppers are locked.
- Build the Input Loader and Pulse Counter
Connect a hopper line from the slices into the 3x12 control area and place your input double chest. Behind the input, wire a comparator, two observers, a 3-tick repeater, and a dropper-hopper latch holding 2 filler items (like ferns), topping unused hoppers with composters to reduce lag.
- Construct the Hopper Triangle and Launcher
Build a 3-hopper triangle loop below the loader path, topping two of the hoppers with composters and leaving one open to interact with the minecart. Lay a sloped track of powered rails and regular rails over the loader, powered by a redstone block.
- Wire the Control Logic
Below the loader platform, run redstone dust, a 1-tick repeater, three target blocks, and a pair of comparators acting as a pulse extender into a redstone torch. This circuit controls when the hopper minecart is held for loading and when it is launched across the slices.
- Lay the Minecart Loop and Uncategorized Slice
Extend the powered and regular rail track across the front of the slice observers and loop it around back across the top of the category filter hoppers. Leave the last chest column without a filter slice so it acts as the overflow output for uncategorized items.
- Add the Waterlogged Leaf Rail Switch
At the end of the slice line, place a downward observer and comparator leading into an upside-down dispenser facing a leaves block (or air block if using powder snow). Put a water bucket inside the dispenser and read the leaves with a comparator to toggle the return powered rails.
- Place Soul Sand Brakes and Indicator Lamps
Place two Soul Sand blocks at the end of the return rail loop so the fast-moving hopper minecart stops cleanly over the unloader without bouncing back. Finally, add redstone lamps read by comparators above the input chest and each storage column to indicate active sorting.
How it works
The ReCategorizer separates item detection from item transport by using a single Minecart with Hopper to test items against category filter chests before opening the matching slice valve:
- Input & Loading: When items are placed in the input double chest, the comparator and observer line wakes up the control circuit. Items flow into the hopper triangle while the hopper minecart is held still, pulling up to a batch of matching items.
- Category Detection: Once loaded, the control circuit powers the launcher rail and sends the hopper minecart across the top of the category filter chests. Because the filter chests have all 54 slots filled, the minecart can only push a single test item into a chest that already contains that exact item type.
- Signal Strength & Valve Opening: When a filter chest accepts the test item, the detection dropper-hopper latch (primed with 16-stackable snowballs and non-stackable shears) shifts its fill level, dropping the comparator output behind the target block. This unlocks the corresponding valve on the lower track.
- Unloading & Reset: As the minecart loops back along the lower rail track in front of the observers, it passes the unlocked slice valve and dumps its remaining items down into that slice's barrel and chest column. The waterlogged leaf dispenser toggles the return rail state, the Soul Sand brakes stop the cart cleanly at the home station, and the reset line primes the detection latch for the next item type. Any item that finds no match in the filter chests is routed into the final uncategorized chest column.
Tips & variations
- Chunk Alignment: Try to build the 3x12 control circuit inside a single chunk, or keep the entire storage room loaded with a chunk loader (or in spawn chunks) so the hopper minecart never unloads mid-cycle.
- Category Configuration Rules: Never leave empty slots inside the upper configuration double chests. Every single slot must hold either an item you want sorted into that column or a non-sortable filler item (like renamed glass panes or shears).
- Lag Optimization: Place composters on top of every horizontal hopper that does not need to pull items from above (except the designated hopper in the control triangle where the minecart interacts).
- Block Types Matter: Pay close attention to where glass blocks, top slabs, and solid blocks are placed in the control wiring so you do not accidentally cut redstone lines or power adjacent rails.





