
Video: 5 to 60 Minute Redstone Clocks - Minecraft by Talmiior
How to build it
- Place the Repeater Base
Start by placing a solid building block on the ground with a second block behind it. Place a redstone repeater on top of the block set to a 2-tick delay.
- Install the Inverter Torch
Place additional building blocks directly in front of your repeater line and attach a redstone torch to the side of the block so that power coming through the repeater will turn the torch off.
- Mount the Dropper
Place a solid block above the redstone torch, then use temporary blocks to position a dropper facing toward the space right above your pressure plate block. Break the temporary blocks once the dropper is facing the right way.
- Add the Pressure Plate and Cover
Place a wooden pressure plate on the block directly in front of the dropper's face. Put a solid block above the pressure plate so dropped items are trapped directly on the plate and cannot pop out to the sides.
- Attach Hopper and Chest Storage
Connect a hopper feeding into the dropper and place a chest (or double chest) on top of the hopper. Fill the storage with cheap, disposable items like sticks.
- Wire for Continuous 5-Minute Cycling (Optional)
For a standalone automated 5-minute clock, route the redstone torch directly back into the dropper so that the moment an item despawns and the torch turns back on, it immediately triggers the dropper to spit out the next item. For a manual 5-minute timer, simply place a button on the back of the dropper instead.
- Chain Modules for 10 to 60+ Minutes
To extend the timer up to an hour, build identical dropper-and-plate modules side by side, offsetting each module's redstone torch so that when the first item despawns after 5 minutes, its torch triggers the next dropper in line.
- Connect the Shared Output Line
Run a shared redstone dust line from all pressure plates to your output, placing redstone repeaters along the line to prevent signal feedback between modules and to boost the signal over longer chains. Add a pulse extender on the output line so the signal stays completely uninterrupted during the tiny pause when one item despawns and the next dropper fires.
How it works
Every dropped item in Minecraft despawns after exactly 5 minutes (6,000 game ticks) inside loaded chunks. This circuit converts that predictable decay time into a redstone signal:
- Active State: When the
dropperfires a stick onto thewooden pressure plate, the plate emits a redstone signal. This powers the main output line and simultaneously runs through a 2-tickredstone repeaterinto the block holding aredstone torch, turning the torch off. - Despawn Trigger: After 5 minutes, the item vanishes and the pressure plate deactivates. The repeater loses power and the redstone torch turns back on.
- Looping or Chaining: In a single automated clock, that torch powers the same dropper to dispense a fresh item right away. In a chained multi-module clock (10 to 60 minutes), the torch instead triggers the next module's dropper in the sequence while a pulse extender bridges the brief transition gap, keeping the main output powered until the final module's item despawns.
- Daylight Variant: If you have sky access, you can also produce 10-minute or 20-minute cycles simply by wiring a
daylight detectorwith a redstone torch inverter to detect day and night transitions.
Tips & variations
- Always cap the pressure plate: If you leave the space above the pressure plate open, items shot from the dropper can bounce off the edge and fail to press the plate. Place a block directly above it first.
- Use renewable junk items: Because this clock works by letting items permanently despawn, load the chests with something nearly free like sticks, seeds, or dirt.
- No Nether required: Unlike Etho hopper clocks that require Nether quartz for comparators, this design only uses basic overworld redstone components, making it ideal for early-game survival or servers where the Nether is locked.
- Long chains need extra repeaters: Redstone dust only carries a signal 15 blocks. When chaining 6 to 12 modules for 30-to-60-minute timers, place repeaters between modules to prevent feedback and add extra pulse extenders at the end so the output never flickers between stages.
- Edition note: The video creator notes in the description that a dedicated Bedrock Edition update exists because torch/repeater timings when chaining modules can behave slightly differently on Bedrock vs Java.





