Long Delay Multiplicative Hopper Clock

A standard Etho hopper clock caps out at around four minutes, which isn't always long enough for large-scale automation. By chaining two hopper clocks together with a single comparator, you can create a multiplicative hopper clock capable of measuring intervals from 10 minutes to nearly a full real-life day. This compact timer is ideal for automated farms, long cooldown systems, or daylight cycle synchronization.

ClocksIntermediateJava Edition
Long Delay Multiplicative Hopper Clock video tutorial

Video: How to Make RIDICULOUSLY LONG Hopper Timer Clocks! by Talmiior

How to build it

  1. Place the First Pair of Hoppers

    Place two hoppers directly next to each other, making sure both nozzles are pointing into each other so they can pass items back and forth continuously.

  2. Add Comparators and Solid Blocks

    Place a redstone comparator facing outward from each end of the two hoppers. Place one solid building block directly in front of each comparator.

  3. Place Redstone Dust and Sticky Pistons

    Put a piece of redstone dust on top of both solid blocks. Then, sneak and place a sticky piston against each comparator (or dust) so the two sticky pistons face toward each other directly above the hoppers.

  4. Place the Redstone Block

    Place a block of redstone on top of one of the hoppers, right in front of one of the sticky pistons. This completes the first standard Etho hopper clock.

  5. Add the Linking Comparator

    To chain a second clock, place a redstone comparator facing sideways out of either one of the hoppers in your first clock.

  6. Build the Second Hopper Clock

    Directly in front of that linking comparator, place another pair of hoppers pointing into each other. Build the exact same Etho hopper clock structure around them (two outward comparators, two blocks with redstone dust, two inward-facing sticky pistons, and one block of redstone on top).

  7. Load the Filler Items

    Insert your calculated number of filler items into one hopper of the first clock and one hopper of the second clock to set your desired time delay.

  8. Connect Your Output

    Take your output signal from the second clock—either by placing redstone dust adjacent to where the redstone block shifts, or by reading one of the second clock's hoppers with an extra comparator running into a repeater or monostable circuit.

How it works

An individual Etho hopper clock works by passing items between two hoppers. A Block of Redstone sits atop one hopper, locking it so it can receive items but cannot push them out. Meanwhile, the unlocked hopper pushes its items into the locked one. Once the unlocked hopper completely empties, its comparator turns off, deactivating the sticky piston while the opposite sticky piston extends and shifts the redstone block to the other side, reversing the cycle.

  • The Chaining Mechanism: A single hopper clock filled with 5 stacks (320 items) takes up to 4 minutes. To multiply this time, a linking Redstone Comparator reads one hopper from the first clock and points directly into a hopper of the second clock.
  • Multiplicative Counting: As long as the first clock's hopper contains items, the linking comparator stays powered and locks the second clock. Only during the brief tick when the first clock's hopper empties completely does the linking comparator turn off, allowing just one single item to transfer inside the second clock.
  • Timing Formula: Because each item transfer takes 0.4 seconds, you can calculate exact timings using the formula x = ((minutes × 60) / 0.4) / 30, where 30 items are placed in the second clock and x items go into the first clock (when taking the output from the second clock's solid block/piston cycle).

Tips & variations

  • Quick Preset Timings (30 items in Clock 2): For a 60-minute clock, put 300 items in Clock 1. For 45 minutes, use 225 items. For 30 minutes, use 150 items. For 15 minutes, use 75 items. For 10 minutes, use 50 items.
  • Multi-Hour Timings: With 5 full stacks in the first clock, 1 item in the second clock equals 4 minutes, 2 items equals 8 minutes, 1 stack (64 items) equals 4 hours 16 minutes, and 5 stacks lasts nearly a full real-life day.
  • Output Placement Matters: Taking the output from the solid block/redstone block side of the second clock gives the calculated time, whereas reading directly off the hopper can double the cycle length unless you halve the items in the first clock.
  • Pulse Shaping: Because the second clock changes states very slowly, routing a comparator output from its hopper into a monostable circuit (pulse limiter) is great for triggering farms with a clean, single pulse.

Frequently asked questions

How many items do I need for a 1-hour hopper clock?
Put 300 stackable items (4 stacks and 44 items) in the first hopper clock and 30 stackable items in the second hopper clock.
Why are my hoppers not passing items to each other?
Make sure both hoppers in each pair are crouched-placed directly into one another so their nozzles connect, and ensure no stray redstone signals are locking them from the sides.
How long can a double chained Etho hopper clock last?
If you fill both the first and second clocks with the maximum of 5 stacks (320 items) each, the timer will last almost a full real-life day (24 hours).

Components used

More long delay timer