Compact Configurable Long-Delay Clock

The traditional Etho hopper clock is a staple of Minecraft redstone, but it maxes out at just over four minutes. By replacing the hoppers with droppers and driving them with a secondary timer, this compact long-delay clock lets you easily configure intervals ranging from a few minutes up to 2.5 hours. It is ideal for automating slow-growing farms, such as amethyst geodes, without having to chain multiple bulky hopper clocks together.

ClocksIntermediateJava & Bedrock
Compact Configurable Long-Delay Clock video tutorial

Video: Slow redstone clocks in Minecraft, compact and configurable (Java/Bedrock 1.19 survival) by FrunoCraft

How to build it

  1. Build the 6x2 Base

    Start by laying down a flat foundation of solid building blocks that is 6 blocks long and 2 blocks wide. In one row, place a solid block on the second position from the left and another on the second position from the right.

  2. Place the Droppers and Comparators

    In the two center spaces between those raised blocks, place two droppers facing directly into each other. Behind each dropper, place a redstone comparator facing outwards so that each comparator points directly into the raised solid block in front of it.

  3. Add the Pistons and Redstone Block

    Place one piece of redstone dust on the very ends of the first row, right next to the raised blocks. In the adjacent second row, place two sticky pistons on the inner side of the dust facing inwards toward each other, and place a single Block of Redstone between their heads.

  4. Load Items into the Dropper

    Open one of the droppers and insert your stackable items to set the timer's duration. With two repeaters on max delay, each full stack of 64 items adds roughly 4 minutes to the total cycle time (up to 9 stacks for about 35 minutes).

  5. Build the Upper Platform

    To build the compact Java Edition controller on top, create a 3x2 platform directly over the middle section. Place a note block (or two note blocks depending on directional update order) directly above the droppers, and fill the rest of the 3x2 platform with solid blocks.

  6. Wire the Torch-Repeater Clock

    Place a redstone repeater on top of the note block facing toward one end of the 3x2 platform, leading into two pieces of redstone dust. Have the dust loop into a second repeater facing the opposite way into a solid block, and attach a redstone torch to the side of that block to complete the upper clock loop.

  7. Adjust Timing and Take Output

    Set the delay on the upper repeaters to control how fast items pulse between the droppers, and place a lever on the upper clock block to pause the timer whenever needed. Take your output signal from either side of the lower redstone block line, which will emit a short pulse every time the items finish transferring.

How it works

This circuit modifies the classic Etho hopper clock by replacing the two hoppers with droppers. Because droppers hold 9 slots instead of 5 and only transfer items when pulsed, the total cycle time can be stretched dramatically.

  • Item Counting & State Switching: The two droppers face each other while a Block of Redstone sits between two sticky pistons. The redstone block locks one dropper by keeping it constantly powered, while the unpowered dropper is free to fire items into the locked one whenever it receives a clock pulse.
  • Comparator Logic: Both comparators read the fill level of their respective droppers. As long as both droppers contain at least one item, both sticky pistons remain extended—one stays extended waiting for the other to retract. Once the active dropper finally shoots its last item into the second dropper, its comparator turns off, allowing its piston to retract and the opposite piston to push the redstone block over, reversing the transfer direction.
  • Secondary Clock & Quasi-Connectivity: The small torch-and-repeater loop on top generates steady pulses. On Java Edition, powering the solid blocks and Note Block above the droppers powers the droppers underneath via quasi-connectivity and block updates, firing one item per cycle.

Tips & variations

  • Java vs. Bedrock Edition: The stacked 6x4x2 design with the note block relies on quasi-connectivity and only works in Java Edition. For Bedrock Edition, build the secondary repeater or comparator fader clock flat on the ground next to the droppers and run redstone dust directly into both droppers so they are powered directly.
  • Note Block Update Order (Java): Depending on orientation and redstone update order, a single note block might only update one dropper. If the clock stalls after half a cycle, move the note block over the other dropper or place note blocks above both droppers.
  • Extending Up to 2.5 Hours: You can expand the top clock to 4 repeaters (reaching ~65 minutes max, or ~7 minutes per stack of items). For even longer delays, replace the upper torch clock with a comparator fader clock: each pair of comparators adds roughly 6 minutes per stack of items, allowing a 6-comparator fader clock to reach about 163 minutes (18 minutes per stack).
  • Pulse Extender Variant: Just like an Etho hopper clock, replacing one of the sticky pistons with a regular piston turns this circuit into a very long configurable pulse extender instead of a free-running clock.

Frequently asked questions

How do I calculate the exact delay of this dropper clock?
With two repeaters set to maximum delay (8 redstone ticks total), each full stack of 64 items gives roughly 4 minutes of cycle time (up to ~35 minutes with 9 stacks). With four max-delay repeaters, one stack equals roughly 7 minutes (up to ~65 minutes). With a 6-comparator fader clock driving the droppers, one stack equals about 18 minutes (up to ~163 minutes).
Why does the compact note block version not work on Bedrock Edition?
The compact vertical version powers the droppers from two blocks above using quasi-connectivity and block updates from a note block, which is a Java-exclusive mechanic. On Bedrock Edition, simply build the small repeater clock to the side and connect it directly to the droppers.
Can I convert this long-delay clock into a timer or pulse extender?
Yes. Replace one of the two sticky pistons with a regular non-sticky piston. The clock will run through one full cycle and then wait until you externally trigger the regular piston side again.

Components used

More long delay timer