Chained Etho Hopper Clock

A standard Etho hopper clock maxes out at 128 seconds, which is too short for many long-term automation tasks. By chaining a primary hopper clock into secondary dropper-based Etho clocks using observers, you can multiply the cycle duration to create custom timers lasting minutes, hours, or even longer. This setup is ideal for AFK farm shutoffs, server unload timers, and delayed farm cycles in Minecraft Bedrock.

ClocksIntermediateBedrock Edition
Chained Etho Hopper Clock video tutorial

Video: Chaining Etho Clocks - Long Duration Clocks Explained Minecraft Bedrock by navynexus

How to build it

  1. Place the First Hopper Pair

    Start the primary clock stage by placing two hoppers facing directly into each other so items can transfer back and forth between them.

  2. Add Comparators and Solid Blocks

    Place a redstone comparator facing outward from each hopper. Place a solid building block directly in front of each comparator, and put a piece of redstone dust on top of both blocks.

  3. Install the Sticky Pistons and Redstone Block

    Next to the hoppers, place two sticky pistons facing each other (one adjacent to each dust block) with a 2-block gap between them for the redstone block. Place a block of redstone in front of one sticky piston so it powers the adjacent hopper.

  4. Load Items for Your Base Interval

    Put stackable items into one of the hoppers to set the base cycle time. Hoppers move 2.5 items per second, so 150 items (2 stacks and 22 items) creates a 1-minute cycle, while 5 full stacks (320 items) gives the maximum 128-second cycle.

  5. Attach the Connecting Observer

    Place an observer watching the piston/redstone side of the first clock so it detects when the cycle completes and outputs a short pulse toward the next module.

  6. Build the Inverted Second Stage with Droppers

    For the second module, build an inverted Bedrock layout so the chain stays flat: place two sticky pistons on the bottom with a block of redstone between them, and place two droppers facing each other above them.

  7. Wire the Inverted Stage

    In Bedrock Edition, place a redstone comparator directly on top of each sticky piston reading outward from the droppers, running into solid blocks with redstone dust to control the pistons below.

  8. Set the Multiplier Items

    make sure the observer from the first clock pulses the droppers of the second stage. Load the exact number of items into the dropper to multiply your first clock's time (for example, 5 items on a 1-minute base clock equals a 5-minute timer, or 60 items equals 1 hour).

  9. Alternate Stages for Longer Timers

    To extend the timer further, continue chaining modules by alternating between the standard layout and the inverted layout, alternating the observer placement from top to bottom on each stage.

How it works

The circuit combines a standard continuous Etho hopper clock with pulsed Etho dropper clocks to multiply time intervals:

  • Stage 1 (Hopper Clock): The block of redstone locks one hopper while the unlocked hopper pushes items into it at a rate of 2.5 items/second (1 item every 8 game ticks). Once the unlocked hopper empties, its comparator turns off, allowing the opposite sticky piston to extend and shift the block of redstone, reversing the flow.
  • Observer Bridge: When a cycle finishes, an observer detects the state change and fires a single pulse into the next module's droppers.
  • Stage 2+ (Dropper Clocks): Droppers do not transfer items automatically; they only push 1 item when pulsed. Because the block of redstone keeps one of the two droppers continuously powered (and therefore unable to react to new pulses), only the unpowered dropper fires 1 item into its partner each time the observer pulses.
  • Multiplication: A dropper holds up to 9 stacks (576 items). If the first clock runs at its maximum 128-second capacity, the second stage takes 128 × 576 seconds to finish, and every additional chained stage multiplies the total duration by up to 576 again.

Tips & variations

  • Always Use Sticky Pistons: While a basic Etho clock can work with regular pistons in Bedrock Edition, normal pistons frequently cause observers to double-pulse when retracting. A double pulse transfers two items instead of one, ruining your timing accuracy. Sticky pistons prevent this issue.
  • Bedrock-Exclusive Placement: This flat chained design relies on placing comparators directly on top of sticky pistons in the inverted modules without them popping off when the piston moves. This only works in Minecraft Bedrock Edition; in Java Edition, you would need to build the chain in a staircase pattern.
  • Why Layouts Alternate: You must alternate between standard and inverted modules (and alternate reading from top and bottom with observers) so the observer never reads directly off the constantly shifting droppers, which would send unwanted pulses down the line.
  • Easy Human-Time Math: Set Stage 1 to 150 items (60 seconds). Set Stage 2 to 60 items (60 minutes / 1 hour). Set Stage 3 to 24 items for an exact 24-hour real-time clock.

Frequently asked questions

How many items do I need for a 1-minute base clock?
Put 150 stackable items (2 stacks of 64 plus 22 items) into the first hopper clock. Since hoppers transfer 2.5 items per second, 150 items take exactly 60 seconds.
Why do the chained modules use droppers instead of hoppers?
Hoppers transfer items continuously as long as they are unlocked. Droppers only transfer one item per redstone pulse, allowing each stage to count the completed cycles of the previous clock.
Can I use normal pistons instead of sticky pistons?
No. In Bedrock Edition, normal pistons often cause the observer to fire twice during a cycle transition, which sends two items instead of one and breaks the timer's accuracy.
Does this exact flat design work in Minecraft Java Edition?
No. The alternating inverted modules place redstone comparators directly on top of pistons, which pop off in Java Edition when the piston extends.

Components used

More long delay timer