22-Minute Long Duration Timer

Need a redstone signal that stays active for several minutes before shutting off on its own? This long-duration timer uses copper bulbs, hoppers, and a slow comparator clock to hold an output signal for up to 22+ minutes. It is ideal for controlling automatic farms, brewing setups, or any contraption requiring a long, consistent delay that resets cleanly on each trigger.

ClocksIntermediateJava Edition
22-Minute Long Duration Timer video tutorial

Video: Minecraft Long Duration Redstone Timer – 22+ Minutes! ⏳🔥 by Keksstube

How to build it

  1. Place the Input Copper Bulb

    Start by placing your first copper bulb on the ground, which will act as your trigger input. Place a redstone comparator reading from the bulb, leading into a solid building block and redstone dust.

  2. Set Up the Target Block and Torch

    Attach a redstone torch and a target block next to the input line. The target block will redirect the redstone dust so it cleanly locks and unlocks one side of the hopper pair.

  3. Connect the Hoppers

    Place two hoppers next to the target block setup so that their nozzles point directly into each other. You can do this by placing the first hopper, placing the second one into it, and then breaking and replacing the first one so it faces the second.

  4. Add Comparators and Observers

    Place a redstone comparator facing outward from each of the two hoppers to detect when items finish transferring. Place two observers looking directly at those comparators to catch state changes.

  5. Place the Second Copper Bulb

    Position your second copper bulb alongside the observer line with a solid building block next to it, and place a comparator reading the signal from this second bulb.

  6. Build the Slow Comparator Clock

    In front of the comparator, build a two-layer structure of solid blocks and add another comparator, redstone dust, and a redstone torch on top. Once wired, this section should begin blinking very slowly.

  7. Connect the Repeater Feedback Line

    Place your final building block, a redstone repeater, and three pieces of redstone dust to bridge the slow blinking clock back to the hopper system. Click the comparator or repeater as shown to set the proper delay mode.

  8. Load Items to Set the Time

    Open one of the hoppers and insert stackable items to configure your duration. You need 2 items as a base, and every additional item adds roughly 4.3 seconds to the total timer duration.

How it works

This circuit combines a toggleable hopper latch with a slow pulsing clock to stretch how long it takes for items to move from one hopper to the other:

  • Triggering the Input: Sending a pulse into the first Copper Bulb toggles its state. Its comparator output shifts which of the two facing Hoppers is powered (locked) via the Target block and Redstone Torch.
  • Slow Item Transfer: Instead of items flowing at normal hopper speed (2.5 items per second), the slow blinking Comparator and torch clock briefly pulses the hopper line. Each pulse lets only one item transfer every ~4.3 seconds.
  • Completion & Reset: While items are moving, the output remains active. Once the active hopper completely empties, the Comparators watching the hoppers change state, triggering the Observers to toggle the second Copper Bulb and shut the output off. The next input signal simply reverses the item flow direction for the exact same duration.

Tips & variations

  • Timing Math: Put 2 stackable items in the hopper as a baseline. Every extra item you add increases the timer by about 4.3 seconds (up to 5 stacks / 320 items for 22+ minutes).
  • Inverting the Output: The output line is normally powered while idle, so it is recommended to invert the output with a redstone torch so your contraption turns ON while the timer counts down.
  • Version Requirement: Because this design relies on Copper Bulbs as compact T flip-flops, it requires Minecraft 1.21 or newer (or 1.20.3+ with experimental features enabled).

Frequently asked questions

How do I change how long the timer stays on?
Add or remove stackable items inside the hoppers. You need 2 base items, and every extra item adds approximately 4.3 seconds to the timer.
Does the timer need time to reset before I can use it again?
No. Once the items finish moving to the second hopper and the timer turns off, the next input signal simply reverses the direction and moves the items back at the exact same speed.
Why is my output always on when the timer is off?
The raw output signal from the timer is active while idle. Place a block with a redstone torch on the output line to invert the signal so it only turns on while counting.

Components used

More long delay timer