Compact Resettable Long Duration Pulse Extender

Standard hopper-based pulse extenders often lock out new inputs until their current cycle completely finishes. This compact 4x4x4 resettable pulse extender by ilmango lets you press the button at any point to instantly reset the countdown back to its full duration. Each item inside the main hopper adds 12 seconds, allowing a single pulse to be stretched anywhere from 12 seconds up to 62 minutes.

Pulse CircuitsIntermediateJava Edition
Compact Resettable Long Duration Pulse Extender video tutorial

Video: Redstone Basics: compact resettable long duration pulse extender by ilmango

How to build it

  1. Build the base hopper timer

    Start by placing two pairs of hoppers facing into each other to form the core of titisurminecraft's hopper timer. Place comparators reading out of the hoppers into solid blocks with redstone torches attached to lock and unlock the hoppers in sequence.

  2. Add the dropper-hopper monostable

    Attach a redstone torch next to the timer output and place a dropper facing directly into a hopper beside it. Put a single stackable item inside this dropper-hopper pair to generate a quick 1-strength pulse every time the hopper timer completes a cycle.

  3. Load the timing items

    Put 1 item in the secondary timer hopper and load your desired amount of stackable items into the primary timing hopper pair. Each item here adds roughly 12 seconds to your pulse duration (up to 320 items for 62 minutes).

  4. Build the comparator decay loop

    On the top layer above the hoppers, place a comparator reading the dropper's hopper into a second comparator set to subtract mode. Loop the output of this comparator back into itself using solid blocks and redstone dust to store signal strength 15.

  5. Connect the stop torch and input

    Use a top slab in the comparator loop so the redstone line doesn't accidentally cut off or power the hoppers below. Run the loop's output into a block holding a redstone torch that locks the hopper timer once the stored signal decays to zero, and place your input button anywhere along the comparator loop dust.

  6. Optional: Convert to a delayed timer or clock

    To trigger a single pulse after the time runs out instead of holding a continuous signal, replace the loop's solid block with a slab and add a second dropper-hopper monostable read by a comparator. To make it an automatic repeating clock, connect the end-of-cycle torch back into the comparator memory loop with a repeater so it re-powers itself to 15 when it hits zero.

How it works

This circuit combines a comparator fader loop with a hopper clock so that the stored signal strength decays at a slow, controlled rate rather than once per redstone tick.

  • Storing and Resetting: Pressing the button directly powers the redstone dust in the comparator loop to signal strength 15. Because the loop connects directly to the input without decaying immediately, pressing the button again at any time refreshes the loop back to 15, resetting the full countdown.
  • Controlled Subtraction: While the comparator loop holds any signal strength greater than 0, the locking redstone torch turns off and allows the underlying hopper timer to run.
  • Stepping Down: Each time the items finish transferring back and forth in the hopper timer, the dropper-hopper monostable fires a brief signal of strength 1 into the side of the subtract-mode comparator. This decreases the stored loop strength by 1 every cycle ( resulting in 12 seconds per item in total across the 15 steps).
  • Shutoff: After 15 subtractions, the comparator loop reaches 0, the locking torch turns back on to freeze the hopper timer in its starting state, and the output turns off.

Tips & variations

  • Timing Math: 1 item in the main hopper equals 12 seconds of total output time. Two items give 24 seconds, and five full stacks (320 items) give the maximum 62 minutes.
  • Use Slabs Carefully: Ensure you use top slabs where the comparator loop crosses over the hopper clock components; solid blocks can accidentally lock the hoppers underneath or cut redstone lines.
  • Flexible I/O: You can place your input button and take your continuous output from any of the redstone dust pieces or solid blocks forming the top comparator loop.

Frequently asked questions

How do I calculate how many items to put in the hopper?
Each item you place in the main timing hopper adds 12 seconds to the total pulse duration. Divide your desired duration in seconds by 12 to get the exact item count (up to 320 items for 62 minutes).
What makes this different from a regular Etho hopper clock pulse extender?
Standard hopper extenders cannot be reset partway through until the items finish moving back. Because this design stores the progress as signal strength 15 in a comparator loop, pressing the button at any point immediately restores the loop to 15 and restarts the full duration.
Can I use this circuit as a repeating clock?
Yes. By routing the torch that turns on when the loop hits zero back into the comparator loop with a repeater, the circuit will automatically re-power itself to signal strength 15 and output a pulse on a repeating schedule.

Components used

More pulse extender