Hopper Item Sorter with Overflow Protection

Standard tileable item sorters can break when a storage chest completely fills up, causing strong comparator signals to bleed into adjacent lanes and empty their filter items. This alternating AB-tileable sorter isolates each lane's redstone dust to provide complete overflow protection. Additionally, it uses a rear-mounted torch and repeater layout so an extra hopper can be placed underneath to pull out any backlogged items once space opens up.

Item CircuitsIntermediateJava Edition
Hopper Item Sorter with Overflow Protection video tutorial

Video: Minecraft 1.5 Item Sorter With Overflow Protection V2.0 by Morilibus

How to build it

  1. Place Storage and Lower Output Hoppers

    Set down your storage chests and run a column of three hoppers behind each slice: a top transport pipe, a middle filter hopper, and a bottom hopper underneath the locked hopper. Because no redstone torch goes directly under the hopper column in this design, the lowest hopper stays unlocked and can always pull items down when the chests have room.

  2. Add the Filter Hopper and Comparator

    Make sure the middle filter hopper points away from the redstone so it does not push items downward on its own. Behind the filter hopper, place a solid block with a redstone comparator facing away from the hopper.

  3. Build Slice A (Alternating Pattern 1)

    Run the comparator output through 2 redstone dust arranged so they do not connect to the neighboring slices. Use a 1-tick repeater to pull signal strength 2 into a block holding a redstone torch at the back of the circuit.

  4. Lock Slice A's Hopper with a Front Repeater

    Run the output of Slice A's redstone torch into a second 1-tick repeater facing forward into a solid block directly behind the hopper below the filter. Keep both repeaters on their default 1-tick delay.

  5. Build Slice B (Alternating Pattern 2)

    Directly beside Slice A, build the offset pattern so its 2 redstone dust sit at a different position and cannot connect to Slice A's dust. Route the comparator into a block, place the 2 dust and first repeater to invert a rear redstone torch, and run that torch into a second 1-tick repeater powering the block behind Slice B's hopper.

  6. Tile the Slices and Configure Filter Items

    Repeat the A and B slices side by side for as many items as you want to sort. Fill the four right-hand slots of each filter hopper with filler items and place your target item in the first slot so the comparator outputs signal strength 2 when a new item enters.

How it works

Traditional tileable item sorters run parallel lines of redstone dust side by side. If one chest completely fills up, its filter hopper backs up to a full stack, outputting a stronger signal that spills into neighboring slices and drains their filter items. This design prevents overflow bleed in two ways:

  • Signal Isolation (AB Tiling): By alternating between two physical layouts (Slice A and Slice B), the 2 redstone dust in each slice are staggered vertically and horizontally so adjacent dust lines never connect. Even if a filter hopper completely fills up, its signal cannot cross into neighboring lanes.
  • Repeater Hopper Locking: Many isolated designs place a redstone torch directly under the locked hopper, which prevents you from placing another hopper underneath and causes items to stay permanently trapped in the middle hopper after an overflow clears. Moving the redstone torch to the back and locking the hopper's adjacent block with a redstone repeater frees the space underneath for an extra pulling hopper.
  • 3-Tick Maximum Delay: When a matching item enters the filter hopper, the redstone comparator reaches signal strength 2. The signal travels through the first 1-tick repeater, turns off the 1-tick redstone torch, and turns off the front 1-tick repeater for just long enough to let one item pass.

Tips & variations

  • Do Not Add Repeater Delay: Each slice uses two repeaters (1 tick each) plus one redstone torch (1 tick), totaling 3 redstone ticks of delay. Do not increase the delay on either repeater—adding even 1 extra tick keeps the hopper unlocked too long and pulls two items out instead of one.
  • Space vs. Self-Clearing Trade-off: Each slice occupies a 1x5x6 footprint (excluding the base support blocks), which is 1 block taller and 1 block deeper than simpler alternating designs that place the torch under the hopper. Use the simpler torch-under-hopper version if space is tight and you don't mind up to one stack remaining inside an overflowed hopper.
  • Feed Items from the Side: When running a hopper pipe across the top of the filters, feed items horizontally into the side of the hopper chain rather than dropping them straight down from above to ensure consistent sorting behavior.

Frequently asked questions

Why use two repeaters per slice instead of putting the redstone torch under the hopper?
Putting a redstone torch directly under the locked hopper blocks you from placing an unlocked hopper beneath it, and the torch also powers the block beside it. If the system overflows, stacks of items get trapped in the hopper and won't drain out on their own when you empty the chests. Using a front repeater leaves space for a pulling hopper underneath so backlogged items automatically clear out.
Why does my sorter pull out two items at a time?
Check your repeaters. Both repeaters in each slice must remain on their default 1-tick setting. Any delay beyond the built-in 2 repeaters and 1 torch keeps the hopper unlocked long enough for two items to pass.
Can I stack this design vertically for a double-decker storage room?
Yes. You can build one row of sorters directly above another and use hopper pipelines and top slabs around the redstone to route items cleanly into your chests without crossing signals.

Components used

More overflow protection