
Video: Minecraft Auto Wood Stripping Machine V1 by RunsWithScissors
How to build it
- Build the Blast Chamber Floor & Collection
Start at the lowest point with a 3-block base and extend a 3x8 platform of leaves off of it. Waterlog every leaf block in the floor, then place a double chest at the collection end with a hopper feeding into it, flanked by a trapdoor and waterlogged leaves.
- Raise the Waterlogged Leaf Walls
Build 4-block-high walls of leaves around the perimeter of the 3x8 floor to contain explosions safely. Waterlog every single leaf block in the walls so the TNT cannot destroy the chamber.
- Create the Feed Slot & Water Stream
On the front wall of the blast chamber, build a leaf frame with a 2-block vertical gap in the middle so pushed logs can enter the chamber. Waterlog the frame and place water source blocks inside the back of the chamber so items flow toward the collection hopper.
- Assemble the Lower Piston Feed Tape
Outside the blast chamber slot, build the lower pushing module using a repeater running into a block, a lever on redstone dust, and two pistons arranged vertically. Place a wall block above the repeater with an observer watching the wall, leading into solid blocks with redstone dust on top.
- Add the Upper Downward Piston & Restock Dropper
At the top of the entry slot, wire three solid blocks with redstone dust leading to a downward-facing piston and a repeater controlled by a main on/off lever. Place a fence on top of the downward piston with an observer watching it, and connect that observer to a dropper fed by a hopper and double chest so it drops fresh logs to the player.
- Construct the Redstone Torch Tower
Directly above the block holding the main control lever, build a vertical torch tower alternating four redstone torches and solid blocks to carry the on/off signal up to the TNT duper level.
- Build the Comparator Clock & Sand Pusher
At the top of the torch tower, build a small platform holding a comparator loop connected to three repeaters set to 4 ticks each (12 ticks total). From this clock, run a 1-tick repeater into a piston pushing a block with a sand or gravel block resting on it.
- Assemble the TNT Duper & Alignment chute
Next to the sand piston, place two opposing pistons facing an observer and a TNT block, topped with solid blocks, a slab between them, and redstone dust. Enclose the drop chute on the side with glass blocks, a wall block, a sign, and a single flowing water source to align the duplicated TNT into the blast chamber, then place the final connecting redstone dust.
- Load and Run the Stripping Machine
Fill the upper double chest with extra logs, put a stack of logs in your off-hand and an axe in your main hand, and place one initial log in front of the top piston. Flip the lever on and hold right-click to strip and place logs continuously.
How it works
This machine combines three synchronized subsystems to automate log stripping:
- Player & Restock Loop: You stand in front of the top piston with logs in your off-hand and an axe in your main hand while holding right-click. You strip the log in front of you and immediately place a new log once it moves. Whenever the downward piston cycles, the fence on top updates an observer, pulsing the dropper to toss a fresh log straight into your inventory.
- Piston Feed Tape: As you place and strip logs, the downward piston pushes the column of stripped logs down toward the lower pistons. The wall-and-observer detection circuit at the bottom senses the column shift and fires the horizontal pistons, shoving the stripped logs through the 2-block slot into the blast chamber.
- Clock, TNT Duper & Blast Chamber: Turning off the main lever unlocks the torch tower and starts the 12-tick repeater/comparator clock at the top. A 1-tick repeater pulses the sand piston to trigger the piston-and-observer TNT duper. The duplicated TNT slides down the water-and-glass alignment chute into the completely waterlogged leaf chamber, blowing up the incoming stripped logs so they flow down the water stream into the bottom chest.
Tips & variations
- Speed Upgrade (Author's Update): Replace the redstone dust feeding into the back of the top comparator with a repeater set to a 2-tick delay facing into the comparator. This increases the machine's rates substantially.
- Anti-Jam Fix (Author's Update): Place a waterlogged leaf block directly above the entry slot on the inside of the blast chamber to prevent incoming logs from getting stuck and blown up before clearing the slot.
- Waterlog Every Leaf: Leaves by themselves have very low blast resistance. Make sure every single leaf block in the floor and 4-high walls is waterlogged before turning on the TNT duper.
- Java Edition Mechanics: This build relies on Java Edition piston-based TNT duplication and wall/fence observer updates, so it will not function in Bedrock Edition without replacing the duper with a TNT dispenser.





