
Video: Redstone tutorial automatic Tree Harvester (improved by PearSquirrel) by eedze
How to build it
- Build the Tree Frame and Ceiling Hole
Place a temporary sapling to mark the center and build a 10-block-high pillar beside it. Bridge across over the sapling and create a single-block ring right above where the trunk will grow so logs can be pushed through the ceiling. Keep at least 2 blocks of horizontal clearance around the trunk up to 9 blocks high so trees can grow unobstructed.
- Dig the Main Redstone Pit
Remove the sapling and dig a 5x7 pit centered around the tree position. This area will house the upper sand-feeding pistons and control wiring.
- Install the Upper Smart Piston
On the 5-wide side under the ceiling hole, count down 3 blocks and place a normal piston facing the center, with a sticky piston behind it. Wire a repeater into the normal piston, place redstone torches and dust in an S-curve around the corner, and add a 1-tick repeater and a 4-tick repeater to create the upper pushing mechanism.
- Dig the Reset Trench and RS NOR Latch
Dig a trench 4 blocks deep and 13 blocks long extending out from the pit. At the start of the trench, build an RS NOR latch using two redstone torches and dust, followed immediately by a small pulse generator using an extra torch, a 1-tick repeater running into a block, dust on top, and a torch on the side.
- Lay the 20-Repeater Delay Line
Run a two-way delay line down and back along the 13-block trench using 20 redstone repeaters in total, all set to maximum (4-tick) delay. Once wired, manually break and replace the latch torch to reset the RS NOR latch so the sticky piston pulls the upper normal piston back.
- Build the Lower Sand Stacker
Dig a shaft 3 blocks wide and 12 blocks deep directly beneath the upper sand pusher. At the very bottom, place one normal piston facing forward and another in the corner facing straight up, then wire them with a repeater, a 1-tick repeater, redstone dust, and a side redstone torch to create a smart piston that automatically pushes falling sand upward.
- Connect Upper and Lower Stackers
Carve a spiraling 3x3 staircase tunnel from the bottom shaft back up to the main pit. Lay a continuous line of redstone dust down these stairs to connect the main activation circuit to the bottom smart piston setup.
- Wire the Dirt Block Swapper and Glowstone Bypass
Place a sticky piston with a dirt block in front of the tree spot and a redstone torch underneath it. Below that, wire a torch tower with a repeater and dust so the dirt automatically pushes back out when the sand column drops to the bottom. Add a glowstone block on the staircase wiring to create a one-way vertical signal bypass that retracts the dirt when triggered.
- Load the Sand and Pressure Plate
Fill the lower vertical column completely with sand up to the upper piston, place one solid block in the gap, and put a final piece of sand on top. Cover the pit with flooring and place a pressure plate next to the dirt block to trigger the harvest cycle.
- Add the Ceiling Log Pusher
At the ceiling hole, place a normal piston facing sideways with a block next to it, powered continuously by a redstone torch (or lever), a repeater, and dust. Whenever a log rises through the ceiling, it completes the circuit and gets pushed sideways into a horizontal row.
- Build the 8-Piston Downward Pusher
At the end of the horizontal log path, place a redstone torch under the 8th block position with dust and a repeater leading up to a row of 8 downward-facing normal pistons. Run redstone dust across the top of all 8 pistons so they push the row of logs downward simultaneously once the row is full.
- Construct the Bottom Harvesting Wall
At the bottom of the downward log chute, build a wall of normal pistons 8 blocks long and 3 blocks high facing outward. Wire a sensor torch and a raised line of redstone dust behind the bottom row driving a row of redstone torches so the entire wall of logs is pushed forward for easy harvesting once logs reach the bottom.
How it works
The harvester works by swapping the dirt block underneath a grown tree with a rising column of sand, then routing the pushed logs into a storage wall:
- Trigger & Dirt Retraction: Stepping on the pressure plate sets the RS NOR latch and sends a signal through the glowstone diode, turning off the torch holding the dirt sticky piston extended. The dirt retracts out of the way.
- Sand Elevator: The active latch powers the upper and lower smart-piston circuits. The bottom upward-facing piston and the upper horizontal piston alternate pushing sand into the vertical shaft and raising it up, shoving the tree trunk straight through the 1x1 ceiling hole.
- Timed Reset: Simultaneously, a pulse travels down the 20-repeater delay chain (set to 4 ticks each). Once the signal reaches the end, it resets the RS NOR latch and retracts the support piston. Gravity drops the sand column back into the lower shaft.
- Dirt Restoration: When the falling sand reaches the bottom, it completes the lower sensor circuit, re-extending the sticky piston with the dirt block so you can plant the next sapling.
- Log Conveyor: At the top, each log pushed through the ceiling completes a smart-piston circuit over an always-on repeater, shoving the logs sideways into an 8-block row. When the 8th log arrives, it powers a line of 8 downward-facing pistons that push the slice down into a 3-high wall of 24 pistons, which eventually pushes the collected wood outward for mining.
Tips & variations
- Keep Growth Clearance Empty: Leave at least a 5x5 area (2 blocks in every horizontal direction from the sapling) clear of blocks up to 9 blocks high, otherwise saplings—especially pine/spruce—will refuse to grow or waste bonemeal.
- Resetting a Stuck Latch: If the upper piston gets stuck extended while building, break and replace the reset torch on the RS NOR latch to clear the state before loading the sand.
- Glowstone Diode Behavior: The dirt retraction circuit relies on Java Edition transparent-block mechanics (introduced in 1.2), where redstone dust on glowstone allows signals to travel upward along a staircase without traveling back downward.
- Adjustable Wall Width: The downward pusher is built 8 pistons wide in the tutorial, which is well within the 12-block piston push limit, but you can shorten it to 5 or 7 blocks wide to fit a smaller base.





