
Video: Block Storage And Fast Extractor by ilmango
How to build it
- Build the 4-Tick Player Input & Filler Dispenser
Set up the input station where a player places blocks (such as sculk) in front of a piston firing every 4 ticks. Adjacent to the input line, install a dispenser clocked at 4 ticks to place powder snow from buckets whenever you want to flush and extract the stored cube.
- Add the Empty Bucket Filter Below the Input
Beneath the powder snow dispenser, build a high-speed hopper minecart item filter to pull empty buckets out of the dispenser and route them over to the extraction end of the machine.
- Construct the 12×12×12 Cube Maker
Route the 1×1 input stream toward the back of the storage area to a bottom piston that pushes rows upward until 12 rows (a 12×12 vertical slice) are formed. Place an observer at the top to detect the 12th row and trigger a 12×12 piston wall that pushes all 144 blocks sideways into the main storage cube.
- Install the Slice-Clearing Flying Machine
At the far side of the 12×12×12 cube, build a flying machine that pushes the outermost 12×12 slice sideways out of the cube whenever the main piston wall advances, then immediately returns so it is out of the way before the next slice arrives.
- Build the Column Pusher & 48-Tick Hopper Clock
In the temporary holding area receiving the 12×12 slice, set up two perpendicular piston arrays to push 12-block columns one step over every 2.4 seconds. Control this cycle using a 48-tick hopper clock.
- Set Up the Zero-Tick Vertical-to-1×1 Converter
At the end of the column pusher, build a zero-tick piston pusher that shifts each 12-block vertical column into position and immediately pushes the blocks downward one by one into a single final horizontal piston, converting the slice back into a continuous 4-tick 1×1 block stream.
- Add the Powder Snow Pickup & Bucket Recycler
Along the output stream, place a dispenser fed with the empty buckets from step 2 and trigger it for every incoming block. Place a hopper minecart below to catch filled powder snow buckets (or ejected empty buckets) and route them through a dropper line and double-speed item sorters back into the 40-double-chest bucket storage.
- Create the Player Mining Station
Direct the final 1×1 output block stream to a mining spot where the player can stand and break incoming sculk blocks at up to 18,000 blocks per hour. Optionally wire a safety line from the output stream to lock the 48-tick hopper clock and block the powder snow dispenser if the player stops mining.
How it works
The contraption converts a 1×1 stream of blocks into a 3D 12×12×12 cube (1,728 blocks) and reverses the process without bottlenecking the 4-tick (5 bps) throughput:
- 1D to 3D Compression: Blocks enter every 4 ticks in a horizontal line. Once a line of 12 reaches the back, a piston pushes the row up. After 12 rows form a 144-block wall, an
observerdetects the top row and fires a 12×12 piston wall to shift the entire slice into the cube. - Displacement via Powder Snow: Because pistons can only push 12 blocks, emptying the cube requires feeding filler blocks into the input. A dispenser places powder snow every 4 ticks, pushing the stored sculk slices through the machine while an under-mounted hopper minecart filter pulls out the empty buckets.
- 3D to 1D Decompression: Each time the 12×12 piston wall pushes a slice forward, a flying machine at the opposite end shoves the oldest 12×12 slice into an extractor bay and immediately returns. A 48-tick hopper clock (2.4 seconds—the exact time needed to process 12 blocks at 4 ticks each) advances one 12-block column at a time.
- Zero-Tick Hand-off: Tight timings use zero-ticked pistons to shift the vertical column into a downward piston feed, pushing blocks one by one in front of a final horizontal piston at 4 ticks per block.
- Closed-Loop Bucket Recycling: An output dispenser fires an empty bucket at every block exiting the stream. If the block is powder snow, it is picked up; if it is a solid block like sculk, the bucket drops out and is caught by a
hopper-minecart, sorted via double-speed sorters, and returned to the 40-double-chest reservoir.
Tips & variations
- Add an Overflow Safety Switch: If the player misses blocks at the mining station, the output line will jam. Power one of the output blocks to detect backups and run a redstone line that both pushes a block in front of the powder snow dispenser and locks a hopper in the 48-tick hopper clock (or use a constant TNT duper at the end of the line).
- Scaling & Chaining: You can chain multiple 12×12×12 cubes in series by feeding the 1×1 output of one extractor into the input of the next, or run 2 to 4 units in parallel and merge their output streams to reach 36,000 XP/hr (or up to 72,000 blocks/hr mining speed).
- Java Edition Mechanics: This build relies heavily on Java-specific zero-tick piston timings, flying machine behaviors, and fast hopper minecart item extraction. It will not function in Bedrock Edition.





