
Video: Pistonless Up and Down binary ripple counters - Minecraft Java/Bedrock by TheDarkness344
How to build it
- Place the Main Repeater Line
Build a raised line of solid blocks and place one redstone repeater on top for each binary bit you want (for example, four repeaters in a row for a 4-bit counter), separated by solid blocks between each repeater.
- Add a 2-Tick Pulse Shortener at the Input
Connect a pulse shortener to the start of the repeater chain so that every count trigger enters the line as a clean 2-tick redstone pulse.
- Build the Lower Torch Towers
Drop a row of blocks down alongside the repeater line and attach redstone torches on both sides beneath each bit slice. Place solid blocks on top of these torches and add another layer of redstone torches facing the direction of the main repeaters.
- Install the Locking Repeaters
Place solid blocks on top of the upper torches and extend a small platform outward for each bit. Place a 1-tick redstone repeater on each slice pointing directly into the side of the main line repeaters to lock them.
- Construct the SR Latches
Behind each locking repeater, build an SR (Set-Reset) latch using two vertical redstone torches, solid blocks above them, and redstone dust on top so that the inside torch powers the locking repeater.
- Connect the Ripple Carry Feedback
Extend the output of each latch outward by two blocks with redstone dust, step up one block, and place a redstone torch feeding back into the previous bit's latch so that when a higher bit turns on, it resets the lower bit back to zero.
- Stabilize the Latches
If any of the vertical torch latches begin flashing or buzzing during construction, temporarily place a button on the latch block and press it once to force the latch into a stable state.
- Wire the Master Reset Line
Run a line of redstone dust behind all the SR latches and place a 1-tick repeater going into the reset block of each bit. Connect a button to this line so you can reset all bits to zero at once without adjacent torches accidentally powering the line.
- Optional: Configure as Down or Modulo-N Counter
To count down, simply invert the outputs with redstone torches so the counter starts at maximum (e.g., 15) and counts down to 0. To reset at a specific number (like 10 for BCD), combine the target bit outputs with an AND gate (for up counters) or an XNOR comparator gate (for down counters) and route that output back into the master reset line.
How it works
Rather than chaining standard T flip-flops—which cannot be easily cleared—this circuit stores each binary bit inside a torch-based SR (Set-Reset) latch paired with a locked repeater line.
- 2-Tick Clock Input: When a 2-tick pulse enters the main repeater chain, it travels down the line until it hits the first unlocked repeater, setting that bit's SR latch to
1. - Repeater Locking: Each latch controls a perpendicular 1-tick repeater pointed into the side of the main line repeater. Depending on the latch state, it locks or unlocks the path for the next incoming pulse to ripple further down the chain.
- Ripple Reset: Whenever a pulse propagates to the next higher bit and sets it to
1, a feedback torch sends a signal backward to reset the preceding lower bit back to0(for example, transitioning from0111[7] to1000[8]). - Master Reset & Bit Preset: Because every bit is an independent SR latch, pulsing the back repeater rail forces all latches to
0simultaneously, while individual buttons on the set side let you manually load any binary number.
Tips & variations
- Input Pulse Length Matters: Always feed the clock input through a 2-tick pulse shortener. A long button press without a monostable circuit will cause the pulse to bleed through multiple stages at once.
- Ripple Delay (Asynchronous): Because each bit waits for the previous bit to toggle, higher bit counts (like transitioning from 7 to 8) exhibit a brief ripple delay with intermediate transition states.
- Modulo-N Down Counters: You can use a simple AND gate on the target bits (e.g., bits 8 and 2 for 10) to auto-reset an up counter, because it reaches 10 from below. However, for a down counter starting at 15, bits 8 and 2 are already active on numbers like 15 and 11—so you must use a multi-bit XNOR gate (equality comparator) to detect the exact target value before triggering the reset.
- Chaining for Decimal Displays: Combine several 4-bit Modulo-10 counters together to create a Binary-Coded Decimal (BCD) counter (ones, tens, hundreds) for 7-segment displays.





