
Video: UNBREAKABLE Auto Crafters | Minecraft Bedrock by OmLedu
How to build it
- Single-Item Crafter Setup (1x or 2x Speed)
For recipes using only one ingredient type (like bone meal or iron blocks), have a comparator read the crafter and compare it against a signal strength of 9 (such as a second crafter with all 9 slots locked pointing into the side via a comparator). Loop the comparator's output back into the crafter using a repeater for single-hopper speed (safe for multi-slot recipes), or use a repeaterless comparator subtract clock for double-hopper speed on single-slot recipes.
- 2-Item Crafter: Hoppers and Barrels
In a 3x5 area, place your main crafter in the front middle, one block above the floor. Point a hopper into the left and right sides of the crafter, place a barrel on top of each hopper, and point two more hoppers down into the top of those barrels.
- 2-Item Crafter: Clock Torch and Repeater
One block behind and one block below the crafter, place a solid block with a redstone torch on its back face, and put a solid block directly above that torch to power the crafter. Place solid blocks on both sides of the torch, then place a repeater on the middle block pointing toward the back.
- 2-Item Crafter: Comparators and Lower Dust
Place a comparator on each of the two outer blocks reading the side-feeding hoppers. Put a solid block in front of the repeater with redstone dust underneath it, plus three more redstone dust in a row across the back floor.
- 2-Item Crafter: AND Gate Torches and Feedback
Extend two solid blocks out of the front of each comparator and attach redstone torches to the back of the furthest blocks so they power the lower dust line. Finally, place a solid block behind each barrel and run three redstone dust down each side from the comparator outputs to the barrels to complete the 2-item crafter.
- 3-Item Crafter: Hoppers and Barrels
To build the 3-item version instead (3x6 area), place the crafter at the front middle, two blocks above the floor. Point three hoppers into the left, right, and back of the crafter, place barrels on top of all three hoppers, and point three top hoppers down into those barrels.
- 3-Item Crafter: Clock Base and Glass
Place a solid block on the floor diagonally back from the space directly underneath the crafter. Put a redstone torch on the back of this block, redstone dust on top of it, and place a glass block on both the left and right sides of that dust (above the torch level).
- 3-Item Crafter: Block Structure and Comparators
Place two comparators on top of the glass blocks reading the left and right bottom hoppers. Behind the barrels, build a row of three solid blocks in front of the comparators, followed by two more rows of three blocks stepping diagonally down and toward the back.
- 3-Item Crafter: Middle Comparator and Staircase
On the middle block of the middle row, place a third comparator pointing toward the back (reading the center hopper through the block) running into a solid block. From that block, build two more solid blocks stepping diagonally up toward the front, placing redstone dust on the lower two so the dust points into the upper block behind the middle barrel.
- 3-Item Crafter: Wiring the Barrel Locks
Place redstone dust on top of the remaining solid blocks around the left and right sides so that all three comparator outputs lead up to the blocks behind the barrels and down toward the back row.
- 3-Item Crafter: Finishing the Clock and AND Gate
At the bottom front, place a repeater pointing toward the back so it is powered by the low redstone torch, and loop redstone dust from the repeater up to the block with dust above the torch. Place four redstone dust along the back floor and attach three redstone torches to the back of the rear blocks to keep the clock locked until all three ingredients are ready.
- Set the Recipe Pattern and Load Items
Fill the crafter slots with full stacks of your desired 2-item or 3-item recipe, lock all unused slots, and only feed new ingredients into the topmost hoppers (never directly into the barrels or bottom hoppers).
How it works
Unlike observer-based designs that rely on a single state change—which can be missed during lag or across chunk boundaries—this circuit uses a continuous redstone torch-repeater clock held in the OFF state by an AND gate.
- Buffer Reading: Because a comparator cannot tell if individual slots inside a crafter are depleted, the comparators instead read the bottom feeding hoppers. The crafter must first completely fill with full stacks of the recipe, allowing items to back up into the feeding hoppers.
- Signal Strength 2 Trigger: Once at least 23 items back up into every feeding hopper, each comparator outputs a signal strength of
2. - Top Hopper Bottleneck: A signal strength of
1constantly powers the block behind the barrel as items trickle through, locking the topmost hopper just enough to regulate item flow and prevent flooding. - Unlocking the Clock: When all comparators reach signal strength
2simultaneously, the signal reaches the back blocks and turns off all the rear redstone torches. With every torch off, the back redstone dust depowers, unlocking the lower torch-repeater clock. - Built-in Underflow Protection: The clock rapidly pulses the crafter until any single ingredient drops below 23 items in its feeding hopper. Immediately, that comparator drops to signal strength
1, its rear torch turns back on, and the clock locks until supplies are replenished.
Tips & variations
- Never Load Lower Containers: Always input items through the topmost hoppers via chests, item filters, or storage lines. Inserting items directly into the barrels or lower feeding hoppers bypasses the hopper lock and can break the timing.
- Adding Overflow Protection: To stop the crafter from dropping items on the ground when your output chest fills up, place a comparator reading the topmost output chest (or through a solid block behind it) and run redstone dust from it directly into the back clock dust line. When the chest fills, it powers the line and locks the clock.
- Fine-Tuning Overflow Capacity: You can point a second comparator into the side of the overflow comparator in compare mode. Use a maximum side signal strength of
14(not15); at15, items already in flight will cause one extra craft after the chest is full. - Single-Speed vs. Double-Speed: Do not use the double-speed repeaterless comparator clock for multi-slot single-item recipes like iron blocks—it pulses one extra time at the end and will accidentally craft pressure plates.





