
Video: How to make 5 HIDDEN STAIRCASES in Minecraft! by Mumbo Jumbo
How to build it
- Design 1 (Wall Staircase): Lay Out the Floor and Wall Pistons
Clear a 3x8 area. At floor level, place two upward-facing sticky pistons stacked vertically for a double piston extender with a floor block on top, then place a single upward sticky piston beside it for the first step and another sticky piston higher up in the wall to push out the upper step.
- Design 1: Add the Top Flush 2x1 Door
At the top of the staircase path in the wall, set up a simple 2x1 flush piston door using horizontal sticky pistons facing out toward the wall so the doorway sits completely flat when closed.
- Design 1: Wire the Double Piston Extender & Dropper-Hopper
From your input block, run redstone dust to the bottom sticky piston and a 4-tick repeater into the lower piston, plus a 1-tick repeater into a block holding a redstone torch on its side. Place an upside-down slab above the torch with dust and a repeater running into the upper piston level, and attach a dropper facing into a hopper (with 1 random item inside) next to the torch, taking a comparator output back through a repeater to finish the retraction pulse.
- Design 1: Connect the Upper Step and Observer Tower
Power the block beneath the single step pistons from your main input line. Run a vertical column of upward-facing observers from the bottom redstone line all the way to the top door, where the top observer pulses a horizontal sticky piston pushing a Block of Redstone to toggle the upper entrance in sync with the stairs.
- Design 2 (3-Wide Floor Staircase): Place the Slime & Piston Array
In a 7x5 footprint, build the back triple piston extender using three vertical sticky pistons topped with slime blocks and floor blocks. In front of that, place a double piston extender column, and in the front row place a line of blocks with slime blocks and floor blocks on their faces to form the 3-wide step profile.
- Design 2: Build the Comparator Pulse Extender
Place your lever input block in the bottom corner and wire it into a 2x3 comparator pulse extender (redstone dust at both ends with comparators facing opposite directions between them). Run the output into a block with a side redstone torch.
- Design 2: Wire the Back Triple Piston Extender
From the torch and pulse extender, run three timed branches to the back vertical pistons: a top line with a 2-tick repeater running into an immovable block, a middle line with a 4-tick repeater into the central block, and a bottom 2-tick repeater line leading up to a redstone torch and an immovable block.
- Design 2: Wire the Front Hybrid Extender
Take a redstone torch output from the input into a line with two 4-tick repeaters, feeding a 3x2 platform of dust that powers 3-tick repeaters into the lower pistons. Branch up to the middle pistons with 1-tick repeaters on the sides and a 1-tick repeater powering the upward extension piston so the front steps retract down next to the slime blocks before being pulled into a diagonal staircase.
- Design 3 (3x4 Staircase Entrance): Place Input and Vertical Pistons
In a tiny 3x4 area, place your input block with redstone dust next to a solid block. Place one upward-facing sticky piston in front for the lower stair and two stacked upward-facing sticky pistons behind it for the upper stair, placing your stair blocks on top.
- Design 3: Add the Dropper-Hopper Double Extender
Run a repeater out of the input block into a block with redstone dust and a redstone torch on top. Next to the torch, place a dropper facing into a hopper returning into that dropper, put one item inside, and take a comparator output from the dropper into the block powering the piston column.
- Design 3: Add the 2-Tick Final Extension Repeater
Place a repeater set to 2 ticks running from the main line back into the redstone dust by the piston block to complete the double piston extension and retraction. Surround the mechanism with matching regular stairs so the center steps drop straight down to reveal a secret walkthrough passage.
How it works
Each of the three tutorials uses piston extenders combined with pulse-shaping circuits to move steps out of the way in the right order:
- Design 1 (Wall Staircase): Flipping the lever powers a single piston for the first step and a double piston extender for the second step. A
4-tickrepeater and a dropper-hopper monostable latch generate the extra retraction pulse needed to pull the top piston and its block all the way back flush with the floor. At the same time, an observer tower carries a 1-tick pulse straight up the wall to toggle a sticky piston with a Block of Redstone, opening the flush door at the top. - Design 2 (3-Wide Floor Staircase): Because the staircase is three blocks wide, slime blocks are used to move three-wide rows together. A comparator decay pulse extender holds the signal long enough for a vertical triple piston extender in the back and a hybrid double extender in the front to fire in sequence, pulling the front blocks down adjacent to the slime blocks before dragging them into a diagonal step formation.
- Design 3 (3x4 Staircase Passage): Adapted from a pillar door, the front stair sits on a single sticky piston while the rear stair sits on a vertical double piston extender. The
2-tickrepeater handles the upward extension sequence, and when turned off, the dropper-hopper latch fires a brief comparator pulse through the block to grab the retracted stair block on the way down.
Tips & variations
- Match Your Wall and Floor Blocks: The video uses iron blocks against coloured concrete so you can clearly see which blocks move. In a survival base, use the exact same block as your wall or floor so the seam is invisible.
- Use Immovable Blocks Around Slime (Design 2): Where repeaters or walls touch the path of the slime blocks in the 3-wide staircase, use obsidian, furnaces, or glazed terracotta so the slime doesn't grab the surrounding redstone wiring.
- Don't Forget the Hopper Item (Designs 1 & 3): Both double piston extenders rely on a single random item inside the dropper-hopper pair. If the top block gets left behind on retraction, check that the hopper feeds back into the dropper and holds one item.
- Java Edition Mechanics: These circuits rely on Java Edition piston timing, quasi-connectivity, and 1-tick sticky piston block-spitting (such as the observer-powered redstone block toggle in Design 1) and will not function reliably on Bedrock Edition.




