Easy Exit Hidden Trapdoor

This compact 3x4 redstone contraption combines a flush floor trapdoor with a bottom slime block launcher. Pressing the surface button drops you straight into your underground room, while hitting the bottom button opens the ceiling and bounces you right back out. It is an ideal, resource-friendly entrance for secret survival bases where ladders or water elevators would ruin the hidden aesthetic.

Piston DoorsBeginnerJava Edition
Easy Exit Hidden Trapdoor video tutorial

Video: Minecraft: The Easy Exit Hidden Trapdoor! [Day 12!] by Mumbo Jumbo

How to build it

  1. Place the Slime Launcher

    Clear a 3x4 footprint for the main circuit. At the bottom center, place an upward-facing sticky piston with a slime block on top; the top of this slime block will be your underground floor level.

  2. Wire the Bottom Button Input

    Run a redstone repeater into the bottom sticky piston and trail redstone dust behind it. Step the redstone dust up a block and attach a button on an adjacent block at player height so you can reach it while standing on the slime block.

  3. Route the Signal Upward

    From the bottom input line, place an upside-down half slab to carry the signal upward without cutting the wire. Continue wrapping solid blocks around with redstone dust on top to climb toward the surface mechanism.

  4. Build the Torch Inverter & Delay

    At the top of your redstone line, place a solid block with a redstone torch attached to it to invert the signal and keep the door closed by default. Place surrounding blocks above and beside the torch, and run a repeater set to 2 ticks into the upper block.

  5. Install the Jeb Trapdoor Pistons

    Place two horizontal sticky pistons facing toward the drop shaft (one above the redstone line and one beside it), then place a third sticky piston facing upward in front of them with your surface floor block on top.

  6. Surround the Slime Block

    Place immovable blocks (such as obsidian, furnaces, or glazed terracotta) on all four sides of the slime block at the bottom floor level so the slime does not grab surrounding floor blocks when firing.

  7. Connect the Surface Entrance Button

    Run a separate button line from the surface directly into the block holding the redstone torch. Fill in the remaining walls and floor around the shaft to conceal all the wiring.

How it works

This contraption links a 1x1 flush piston trapdoor with a timed vertical slime launcher:

  • Default State (Closed): The redstone torch powers both the horizontal sticky pistons and the 2-tick redstone repeater. The horizontal pistons push the vertical sticky piston and floor block over the shaft, while the 2-tick repeater powers the upper block to extend the vertical piston flush with the upper floor.
  • Entering from the Top: Pressing the surface button directly powers the block holding the redstone torch, turning the torch off. The vertical piston unpowers first to pull the floor block down, and 2 ticks later the horizontal pistons retract it out of the shaft so you fall through. Because the upside-down slab acts as a one-way diode going up, the signal does not travel down to the slime launcher.
  • Exiting from the Bottom: Pressing the bottom button splits the signal. One path travels up the slab ladder to turn off the redstone torch and open the flush trapdoor above you. The other path runs through the bottom repeater into the upward sticky piston, launching you off the slime block and through the open shaft before the button pulse ends and the trapdoor closes behind you.

Tips & variations

  • Use Immovable Floor Borders: Always surround the bottom slime block with immovable blocks like obsidian, furnaces, droppers, or glazed terracotta. Standard building blocks will stick to the slime and break the circuit.
  • Slab Directionality: Make sure you use an upside-down top slab for the vertical wire climb. This prevents the surface button signal from traveling downward and needlessly firing the slime block while you are dropping in.
  • Java vs. Bedrock Notes: The flush trapdoor relies on Java Edition piston timing and block powering to smoothly push, pull, and power the upward-facing sticky piston. In Bedrock Edition, pistons travel slower and lack quasi-connectivity, so the trapdoor timing may need extra repeater delay to avoid launching the player into a closed ceiling.

Frequently asked questions

Why does my slime block get stuck or break the bottom floor?
Slime blocks pull any adjacent movable blocks along with them. Replace the four floor blocks directly touching the sides of the slime block with immovable blocks such as obsidian, furnaces, or glazed terracotta.
Why am I hitting my head on the trapdoor block when launching out?
Check that your upper redstone repeater is set to 2 ticks and that you are using a standard stone button. If the launcher fires too early, increase the delay on the bottom repeater feeding into the slime launcher piston so the ceiling has time to retract first.
How do I open the trapdoor from the surface without firing the slime launcher?
Wire your surface button directly into the block holding the redstone torch near the top pistons. Because the bottom input uses an upside-down half slab to send power up, the signal from the top cannot travel backward down to the launcher.

Components used

More trapdoor / floor door