Etho Hopper Clock Variants

The Etho hopper clock is one of the most reliable and customizable timers in Minecraft, letting you set precise intervals from a couple of seconds up to several minutes. This guide covers four essential versions of the circuit: the flat traditional design, a 1-wide vertical build, a dustless tileable version, and a one-time pulse extender for farms and lighting displays.

ClocksBeginnerJava Edition
Etho Hopper Clock Variants video tutorial

Video: How to Build All the Redstone Hopper Clocks (1.19+) | Minecraft Tutorial by CubeProspector

How to build it

  1. Traditional Clock: Place the Hoppers and Comparators

    Place two hoppers directly facing into each other so items can transfer back and forth endlessly. Place a redstone comparator facing outward from both ends of the hopper pair, with each comparator running directly into a solid building block.

  2. Traditional Clock: Add Pistons and Redstone

    Place one piece of redstone dust next to each solid block, alongside the comparators. Place two sticky pistons next to the hoppers facing each other, and put a block of redstone against one piston face.

  3. Traditional Clock: Add Items and an Off Switch

    Drop your desired number of stackable items into one of the hoppers (for example, 8 items for a quick test cycle) to start the clock. To pause the clock at any time, place a lever on top of one of the solid blocks and flick it on.

  4. Variant 2 (Vertical 1-Wide): Base Setup

    Start with the same base line: two hoppers facing each other, a comparator facing out of each end, and a solid block in front of each comparator. Instead of placing redstone dust to the side, place one piece of redstone dust directly on top of each solid block.

  5. Variant 2 (Vertical 1-Wide): Upper Pistons

    Place your two sticky pistons on top of the comparators, facing inward toward each other over the hoppers. Place the block of redstone between them and add items to the hoppers to run this 1-wide vertical clock.

  6. Variant 3 (Tileable): Replace Dust with Torch Towers

    To place multiple vertical clocks directly side-by-side without the redstone dust cross-powering, remove the two pieces of redstone dust on top of the end blocks. Place a redstone torch on the outer side of each solid block, a solid block above each torch, and a second redstone torch pointing inward toward the sticky pistons to power them independently.

  7. Variant 4 (One-Time Clock): Modify One Side

    Build the traditional flat clock, but only put redstone dust on one end; on the opposite solid block, place a redstone torch on its side facing the sticky piston. On the side without the torch, replace the redstone dust with a third comparator facing into the sticky piston.

  8. Variant 4 (One-Time Clock): Build the Trigger Latch

    Behind that third comparator, place a dispenser (or dropper) facing into a third hopper that feeds straight back into it, and put a single item inside. Place a solid block on top of the dispenser with a redstone torch on its side, a block above that torch, redstone dust on top of the hopper, and a button on the solid block to trigger a single timed cycle.

How it works

All four designs rely on the same core loop between two hoppers and a movable block of redstone:

  • Locking and Transferring: The block of redstone constantly powers one of the two hoppers. A powered hopper is locked and cannot push items out, but it can still have items pushed into it by the unpowered hopper.
  • Comparator Detection: While the unpowered hopper empties its inventory into the locked hopper, its comparator stays on. Once the unpowered hopper is completely empty, its comparator turns off, while the full hopper's comparator reaches maximum signal strength.
  • Piston Flip: When the full hopper's comparator powers the solid block and adjacent redstone dust (or dual-torch inverter in the tileable build), it extends its sticky piston. Because the empty side's piston has just retracted, the block of redstone is pushed over to the opposite hopper, reversing the flow of items.
  • One-Time Pulse Cycle: In the fourth variant, pressing the button fires one item from the dispenser into the hopper, allowing the third comparator to power the piston and flip the redstone block once. When the main hoppers finish transferring their items back, the clock resets and waits for the next button press instead of looping.

Tips & variations

  • Calculating Time: Hoppers transfer 2.5 items per second (4 redstone ticks per item). Multiply the number of items you put inside by 0.8 seconds to get the full back-and-forth cycle time, or by 0.4 seconds for a single state length.
  • Pausing the Clock: Always attach a lever to one of the end blocks or directly onto a hopper when hooking this up to a mob farm so you can lock the circuit and stop piston noise when not in use.
  • Tileable Spacing: Always use the torch-based tileable variant (Variant 3) if you want independent clocks right next to each other; the standard vertical version uses redstone dust which will bleed signal into adjacent slices.

Frequently asked questions

How do I change the speed of an Etho hopper clock?
Add or remove items inside the hoppers. Fewer items make the clock flip back and forth much faster, while up to 5 full stacks (320 items) will give you a several-minute delay.
Why are my sticky pistons both stuck extended?
Both hoppers currently have items inside them at the same time. Remove the block of redstone, let all items funnel completely into one single hopper, and then place the block of redstone back down.
Why can't I tile the standard 1-wide vertical hopper clock?
The standard vertical design uses redstone dust on top of the end blocks. If you build two right next to each other, the dust connects and triggers neighboring pistons out of sync. Replacing the dust with two vertical redstone torches prevents cross-talk.

Components used

More hopper clock