Tileable Etho Hopper Clock

The classic Etho hopper clock is one of the most reliable adjustable timers in Minecraft, using items transferring between two hoppers to set the delay. However, the standard flat design uses redstone dust on the ends, which connects and breaks if you place two clocks directly next to each other. This simple modification replaces that dust with redstone torches, making the clock completely 1-wide tileable for compact, multi-timer contraptions.

ClocksBeginnerJava Edition
Tileable Etho Hopper Clock video tutorial

Video: Minecraft: Tileable Etho Hopper Clock Tutorial (Redstone Advent Calendar) by xisumavoid

How to build it

  1. Place the Hopper Pair

    Start by placing two hoppers feeding directly into each other so items can cycle endlessly back and forth between them.

  2. Add the Comparators

    On both outer ends of the hoppers, place a redstone comparator facing outward (reading the contents of each hopper).

  3. Place the End Blocks

    Place one solid building block directly in front of each comparator.

  4. Install the Redstone Torches

    Instead of using redstone dust, attach a redstone torch to the side of each building block facing back toward the hoppers, and place another redstone torch directly on top of the building blocks (or in a vertical torch configuration to power the pistons above).

  5. Mount the Sticky Pistons and Redstone Block

    Above the comparators, place two sticky pistons facing inward toward each other, positioned in front of the upper torches. Place a single Block of Redstone between the two sticky pistons above one of the hoppers.

  6. Load Items to Start the Clock

    Place your desired number of stackable items into one of the hoppers. The clock will immediately begin running, shifting the redstone block back and forth.

How it works

This circuit operates on the same item-transfer principle as the standard Etho hopper clock, but keeps the signal strictly within a 1-block width:

  • Hopper Locking: The Block of Redstone sits directly above one of the two hoppers, locking it so it cannot push items while allowing the unlocked hopper to transfer its items into the locked one.
  • Comparator Detection: As long as the transferring hopper still has items, its Redstone Comparator outputs a signal into the solid end block. Once that hopper completely empties, the comparator turns off.
  • Torch Inversion & Piston Trigger: Instead of using redstone dust (which would cross-connect with neighboring slices), the end block uses Redstone Torches to invert and pass the signal upward to the Sticky Piston. When the comparator turns on or off properly at the end of a cycle, the active piston switches states, pushing the redstone block over the other hopper and reversing the flow of items.
  • Timing Calculation: Each item takes 0.4 seconds to transfer from one hopper to the other. For example, 5 items take 2 seconds to travel one way (or 4 seconds for a full back-and-forth cycle if taking output from only one end).

Tips & variations

  • Why It's Tileable: Because there is no exposed redstone dust on the ends of the circuit, you can build multiple copies directly next to each other (1-wide tileable) with completely independent timings in each slice.
  • Timing Math: Multiply the number of items by 0.4 seconds to get the half-cycle time (when taking an output from both sides), or by 0.8 seconds for a full round-trip cycle (when reading from just one side).
  • Taking an Output: You can read the clock's state from the redstone block, the torches at either end, or by placing a redstone lamp/repeater next to one of the end blocks.

Frequently asked questions

Why doesn't the standard Etho hopper clock tile side by side?
The classic flat design places redstone dust next to the solid blocks on each end. If you build two clocks directly adjacent to each other, the redstone dust lines connect across slices and interfere with neighbouring timers.
How do I calculate the time delay for this hopper clock?
Every item added to the hopper adds 0.4 seconds per transfer direction. For example, 5 items equals 2 seconds per side, or 4 seconds for a full back-and-forth cycle from one side.
What are the dimensions of this tileable hopper clock?
Each unit is 1 block wide, 2 blocks tall, and 8 blocks long (1x2x8).

Components used

More hopper clock