Etho Hopper Clock

The Etho Hopper Clock is one of the most popular and reliable adjustable timers in Minecraft redstone. By simply changing the number of items inside its hoppers, you can customize the clock period from less than a second up to several minutes. It is ideal for automating farms, periodic lighting, or any contraption that needs a steady, configurable pulse.

ClocksBeginnerJava Edition
Etho Hopper Clock video tutorial

Video: Minecraft Etho Hopper Clock in 3 minutes by iMineCrazy

How to build it

  1. Connect Two Hoppers Together

    Place a temporary block or hopper down, then crouch (sneak) and place a second hopper directly into the side of it. Break the first one and crouch-place it back into the second hopper so both nozzles point directly into each other.

  2. Add the Comparators

    On both outer ends of your two-hopper line, place a Redstone Comparator facing outward, reading the contents of each hopper.

  3. Place the Solid Blocks

    Put one solid building block directly in front of each comparator so the comparator outputs its signal into the block.

  4. Lay the Redstone Dust

    Place one piece of Redstone Dust next to each solid block, right beside the comparators.

  5. Position the Sticky Pistons

    Next to the hoppers (in line with the two pieces of redstone dust), place two Sticky Pistons facing inward toward each other. There should be a two-block gap between the piston faces right alongside the hoppers.

  6. Insert the Redstone Block

    Place your Block of Redstone in front of either sticky piston so it sits directly beside one of the hoppers.

  7. Load Items to Set the Timer

    Open one of the hoppers and insert the number of items you want for your delay. Once the items finish transferring to one side, the pistons will shift the redstone block and start the cycle.

  8. Take Your Output Signal

    You can pull a continuous half-cycle output from the redstone block Positions, or place a Redstone Repeater reading from one of the end blocks or redstone dust points to send a pulse to your machine.

How it works

The Etho Hopper Clock works by locking and unlocking two hoppers that constantly feed items back and forth:

  • Locking One Hopper: The Block of Redstone sits next to one of the two hoppers, powering and locking it so it cannot push items out. Meanwhile, the unpowered hopper is free to push all of its items into the locked one.
  • Emptying and Switching: While items are still leaving the unlocked hopper, its Redstone Comparator outputs a signal into the solid block and adjacent Redstone Dust, keeping the nearby Sticky Piston extended.
  • Flipping the State: As soon as the unlocked hopper completely empties, its comparator turns off and its sticky piston retracts. Because the other hopper is now full of items, its comparator and piston are already powered, pushing the Block of Redstone over to the opposite side.
  • Reversing Direction: The newly locked hopper now holds the redstone block, unlocking the full hopper so the items immediately flow back in the opposite direction, repeating the cycle endlessly.

Tips & variations

  • Timing Math: According to the video, a single item creates a cycle of about 0.75 seconds, and each additional item adds roughly 0.8 seconds to the total cycle time.
  • Short Pulse Output: If you need a quick 1-tick pulse every time the clock flips rather than a long signal, take your repeater output from the redstone dust/end block right as the pistons switch states.
  • Silent Variant: If the piston noise bothers you, you can replace the sticky pistons with regular pistons so the redstone block is simply pushed back and forth without retraction clicks.
  • Common Mistake: Always double-check that the two hoppers are actually pointing into each other. If one points down into the ground, the items will never transfer.

Frequently asked questions

How do I change the speed of an Etho Hopper Clock?
Simply add or remove items inside the hoppers. Fewer items make the clock cycle faster, while up to 5 full stacks (320 items) create a much longer delay.
Why is my hopper clock stuck on one side?
Make sure both hoppers are pointing directly into each other and that you used Sticky Pistons. If you use regular pistons, the clock only works after the opposite hopper receives items to push the block back.
Where do I connect my redstone output?
You can place redstone dust or a repeater next to either solid block at the ends of the clock, or directly adjacent to one of the two positions where the Block of Redstone rests.

Components used

More hopper clock