Vertical Redstone Signal Transmission

Sending a redstone signal vertically between floors or down into a deep pit normally requires bulky staircases of blocks and redstone dust. Using redstone torch towers, you can transmit signals straight up or straight down in a very tight vertical space. This tutorial covers both the 1x1 upward torch tower and the 1x2 downward torch ladder shown in the video.

Signal TransmissionBeginnerJava Edition
Vertical Redstone Signal Transmission video tutorial

Video: How to make a vertical redstone signal! - Minecraft by Gemini.

How to build it

  1. Upward Signal: Place the Base Block and Torch

    To send a signal straight up, start at the bottom by placing a solid block on the ground and putting a redstone torch directly on top of it.

  2. Upward Signal: Stack Blocks and Torches

    Place another solid block directly above the redstone torch, then place a second redstone torch on top of that new block. Notice how the bottom torch powers the block above it, turning the second torch off.

  3. Upward Signal: Repeat and Connect Input/Output

    Continue alternating blocks and redstone torches straight up until you reach your desired height. Attach a trapdoor (or other output) at the top, and run a line of redstone dust with a lever into the bottom block to toggle the tower.

  4. Downward Signal: Place the Top Torch

    Because redstone torches do not power the block underneath them, sending a signal straight down requires a different layout. Start near the top by placing a solid block with a redstone torch attached to its side.

  5. Downward Signal: Add the Lower Catch Block

    Leave a one-block air gap directly beneath that hanging redstone torch, and place a solid block two blocks below the torch.

  6. Downward Signal: Place Dust and Next Torch

    Put a dot of redstone dust on top of that lower block, and attach a new redstone torch to the side of the same block. The upper torch will power the dust below it, turning the lower torch off.

  7. Downward Signal: Repeat Downwards and Test

    Repeat this pattern as far down as you need: place a block two spaces below the previous side-torch, put redstone dust on top of it, and place a torch on its side. Put a lever at the very top block and a trapdoor at the bottom to test your downward signal.

How it works

Both vertical circuits work by chaining NOT gates (signal inverters) together:

  • Going Up (1x1 Tower): A redstone torch strongly powers the solid block directly above it. Any redstone torch placed on top of a powered block turns off. When you power the bottom block with a lever and redstone dust, each torch in the column flips its state in sequence from bottom to top.
  • Going Down (1x2 Ladder): A redstone torch cannot power a block directly beneath it through another torch, Setups that go down use a side-mounted torch to power a piece of redstone dust sitting on a block directly below it (with one air space in between). That powered dust powers the block it sits on, inverting the next side-mounted torch below.

Tips & variations

  • Even vs. Odd Torches: Every redstone torch in the chain inverts the signal (ON becomes OFF, OFF becomes ON). If your trapdoor or device at the end is open when you want it closed, either add/remove one torch stage or flick your input lever.
  • Signal Delay: Each redstone torch adds 1 redstone tick (0.1 seconds) of delay. Over very tall distances, you will see a brief delay between flicking the lever and the output activating.
  • Common Mistake: You cannot simply build the 1x1 upward torch pillar and expect to power it from the top—torches only read power from the block they are attached to (underneath or on the side), never from above.

Frequently asked questions

Why doesn't the 1x1 torch tower work going downwards?
A redstone torch only changes state when the block it is attached to is powered. In a 1x1 vertical stack, each torch is attached to the top of the block below it, so powering the top of the tower has no way to affect the blocks underneath.
Why is my output inverted at the end of the torch tower?
Every redstone torch acts as an inverter. An odd number of torches will invert your input signal, while an even number of torches will keep the output matching your input.
Can I build this in Survival mode?
Yes, both vertical transmitters only require basic solid blocks, sticks, and redstone dust, making them very cheap for survival bases, mineshafts, and drawbridges.

Components used

More vertical (upwards)