Bedrock Long-Range TNT Cannon

TNT physics in Minecraft Bedrock Edition often limit traditional cannons to short distances, or cause projectiles to explode prematurely in mid-air. This compact, dispenser-based long-range TNT cannon uses an ice-floored water barrel, a ladder stop, and a precise eight-repeater delay line to launch primed TNT around 100 blocks away. It is great for minigames, siege battles, or clearing terrain from a safe distance.

TNT & CannonsBeginnerBedrock Edition
Bedrock Long-Range TNT Cannon video tutorial

Video: Minecraft Bedrock - TNT CANNON 💣 Long Range💥 Tutorial - PS4 , MCPE , Xbox , Windows & Switch by Skippy 6 Gaming

How to build it

  1. Place the 6 Propellant Dispensers

    Start by placing six dispensers facing inward around a central water channel. Arrange them in a compact U-like cluster at the rear so all six will drop their TNT directly into the back of the barrel.

  2. Wire the Rear Dispensers

    Go behind the propellant dispenser cluster and crouch-place redstone dust so all six dispensers are connected and will fire simultaneously when the button is pressed.

  3. Build the 8-Repeater Delay Line

    Branching off from the rear redstone dust, lay out a delay chain along the side of the cannon using 8 redstone repeaters (arranged in rows leading forward and stepping up one block at the end) connected with redstone dust at the corners. Set every single repeater to 4 ticks (maximum delay).

  4. Install the Ice Barrel Floor

    Extend the base of the barrel forward and place the 2 ice blocks at the front end of the floor channel. The slick surface reduces friction so the propellant TNT slides forward smoothly.

  5. Mount the Projectile Dispenser

    At the front end of the delay line, place a solid block with the 7th dispenser on top facing into the front of the barrel. Run the final repeater into the solid block beside/under it so the delay line powers this front dispenser last.

  6. Add the Ladder and Water Source

    Enclose the sides of the barrel with solid blocks and glass. Attach 1 ladder to the inside wall near the front over the ice to hold back the water and align the projectile, then place your water bucket at the very back of the channel.

  7. Cap the Barrel Roof with Glass

    Place glass blocks over the top of the barrel and directly above the firing point. This ceiling prevents the projectile TNT from launching in a high upward arc and exploding in mid-air before hitting the ground.

  8. Attach the Button and Load TNT

    Crouch-place the stone button on the back of the propellant dispenser line. Fill all 7 dispensers equally with TNT, press the button, and watch the projectile launch downrange.

How it works

This cannon separates the TNT into two stages: a 6-TNT propellant charge and a 1-TNT projectile.

  • Instant Ignition (Propellant): Pressing the stone button immediately powers the redstone dust at the back, triggering all 6 rear dispensers at once. The six primed TNT entities drop into the water stream and get pushed forward across the 2 ice blocks toward the ladder. Because they sit inside water, their explosion deals no block damage to the cannon itself.
  • 32-Tick Delay (Projectile): At the same time, the button signal enters the chain of 8 redstone repeaters, each set to 4 ticks (32 redstone ticks total). Just before the rear propellant charges detonate, the delayed signal reaches the solid block powering the 7th front dispenser.
  • Flat Trajectory Launch: The front dispenser drops the projectile TNT onto the ladder right as the six propellant TNT explode behind it. The glass ceiling above the barrel forces the blast vector forward at a flatter angle instead of lobbing it high into the sky, allowing the projectile to cover roughly 100 blocks before its fuse runs out on impact.

Tips & variations

  • Never skip the top roof blocks: If you leave the top of the front barrel open, the projectile will shoot way too high in a steep arc and detonate harmlessly in the air.
  • Keep all 8 repeaters on 4 ticks: Reducing the repeater delay fires the projectile too early, meaning its fuse expires mid-flight before reaching the ground.
  • Use packed ice or blue ice near light sources: Regular ice works well, but if you build near torches or in warm lighting, packed ice prevents accidental melting.
  • Rapid-fire comparator variant (Caution): You can replace the final repeaters with a redstone comparator in subtract mode looping into dust to fire multiple projectile TNTs per shot, though in Bedrock Edition this can reduce range reliability or cause mid-air detonations if mistimed.

Frequently asked questions

Why does my TNT explode in mid-air before hitting the ground?
Either your repeaters are not all set to 4 ticks (causing the projectile TNT to spawn too early), or you forgot to place the blocks directly over the front of the barrel, which stops the TNT from lobbing too high.
Why did my TNT cannon blow itself up?
Make sure you placed the water bucket at the very back of the inner barrel before firing, and double-check that all 7 dispensers have TNT inside—if the rear dispensers run empty while the front one fires, or if the water stream is blocked, the cannon can break.
Does the ice at the bottom of the barrel actually matter?
Yes. The two ice blocks at the front of the trough reduce sliding friction for the six propellant TNT charges so they gather tightly behind the projectile on the ladder before exploding.

Components used

More tnt cannon