Silent Compact Dual Edge Detector

A dual edge detector generates a short pulse both when an input turns on (rising edge) and when it turns off (falling edge), essentially letting a lever behave like a button. This ultra-compact 3x2x1 design uses zero pistons, making it completely silent and ideal for tight redstone contraptions where noise or space is a concern. By matching repeater and torch delays, it creates an instant 0-tick off-on pulse every time your input is toggled.

Pulse CircuitsBeginnerJava Edition
Silent Compact Dual Edge Detector video tutorial

Video: Silent, Compact Dual Edge Detector (Minecraft 1.9) by emeraldfyr3

How to build it

  1. Place the Input Block and Torch

    Place a solid block with a lever attached to it to serve as your input. Attach a redstone torch to the side of this block so the lever toggles the torch on and off.

  2. Set Up the Torch Repeater Path

    Place a redstone repeater directly in front of the redstone torch, facing away from it. Leave this repeater set to its default 1-tick delay.

  3. Create the Parallel Repeater Path

    Run a second path from the input block right beside the torch path. Place a second redstone repeater facing the same direction as the first, and right-click it once to set it to a 2-tick delay.

  4. Merge into the Output Wire

    Place redstone dust in front of both repeaters so that both paths power the same output line. Whenever you flip the lever, this wire will stay powered except for a brief 0-tick off-on flicker.

  5. Add a Dropper-Hopper Pulse Lengthener (Optional)

    To convert the 0-tick off-pulse into a standard positive redstone pulse, place a dropper at the end of the output wire facing into a hopper (and point the hopper back into the dropper). Put a single item inside and take a redstone comparator output from the hopper.

How it works

This circuit relies on matching total delays across two inverted paths while exploiting how Minecraft schedules repeater and torch updates within the same game tick:

  • Matched Delays: A redstone torch has a natural 1-tick delay. By placing a 1-tick repeater after the torch, the inverted path has a total delay of 2 redstone ticks. The parallel non-inverted path uses a single repeater set to 2 ticks, making both paths equal in delay.
  • Sub-Tick Update Order: Without the repeater after the torch, one component updates before the other asymmetrically, causing the wire to only pulse on one edge. Routing both sides through repeaters aligns the sub-tick execution order so that on both rising and falling edges, whichever repeater is turning off always de-powers the output wire slightly before the other repeater turns on within the very same tick.
  • 0-Tick Dual Edge Output: Because the output wire is normally held ON by one of the two repeaters, flipping the lever causes the wire to turn OFF and back ON in the same tick (an inverted 0-tick pulse).

Tips & variations

  • Using the Output: Because the raw output is a normally-on wire that briefly turns off and on in the same tick, connecting a Dropper directly to the output line will trigger the dropper every time the lever is flipped.
  • Standard Redstone Output: If you need to power a redstone lamp or standard circuitry that requires a longer, normally-off pulse, use the dropper-into-hopper attachment with one item inside and read the hopper with a comparator.
  • Burnout-Free Variant (4x2x1): If your input toggles very rapidly, the redstone torch could burn out. You can replace the torch with a Redstone Comparator set to subtract mode (powered from behind by a constant full signal and from the side by a container like a furnace holding 1 item) to achieve an instant/burnout-free inversion in a 4x2 footprint.
  • Edition Warning: This circuit depends heavily on Java Edition's strict sub-tick tile tick ordering. It will not function reliably on Bedrock Edition, where repeater and torch update order differs.

Frequently asked questions

Why does the output redstone dust look like it stays on all the time?
The output wire turns off and back on inside the exact same game tick (a 0-tick pulse). The visual redstone dust does not appear to turn off to the naked eye, but redstone components like droppers connected to the wire will still activate every time you flip the lever.
Why can't I just use a torch and a 1-tick repeater without the second repeater?
In Minecraft Java Edition, repeaters are processed before redstone torches within a single tick. Without a repeater after the torch, the circuit only pulses on one edge because on the other edge the repeater turns on before the torch turns off, keeping the wire continuously powered.
How do I prevent the redstone torch from burning out on fast inputs?
You can build the 4x2 variant that replaces the redstone torch with a comparator in subtract mode reading a container with one item, which eliminates torch burnout completely.

Components used

More dual-edge detector