Adjustable Pulse Limiter

A redstone pulse limiter (also known as a monostable circuit) shortens a sustained redstone signal into a brief, controlled pulse. This circuit is essential when you want a continuous input, like a lever, to trigger an output for only a specific number of ticks. By adding a simple repeater loop, you can easily adjust the exact duration of the output pulse to fit your contraption's needs.

Pulse CircuitsBeginnerJava Edition
Adjustable Pulse Limiter video tutorial

Video: Redstone Pulse Limiter Tutorial by Rails2Revolution

How to build it

  1. Dig the Cutoff Trench

    Dig a single 1-block deep hole in the ground. Place one piece of redstone dust inside the hole, one piece on the ground directly in front of it, and one piece on the ground directly behind it to form a line of three.

  2. Place the Input Blocks

    To the right of the back redstone dust, stack two solid building blocks vertically. Attach your lever (or other activation source) to the back face of this two-block pillar.

  3. Position the Sticky Piston

    Place one solid block on the ground directly to the right of your two-block pillar. Next to that block, place a sticky piston on the ground facing left toward the top block of your pillar (so when it extends, it pushes that top block over the 1-block hole).

  4. Wire the Short Pulse Circuit

    Place a piece of redstone dust on top of the two-block pillar, and another piece of redstone dust on top of the single solid block to its right. At the front end of your ground redstone line, place a redstone lamp to test the output.

  5. Test the Basic Pulse Limiter

    Flip the lever on. The lamp will flash on for a fraction of a second before the sticky piston pushes the block over the hole, cutting off the redstone line.

  6. Extend the Platform for a Longer Pulse

    To make the pulse duration adjustable, extend the two-block-wide section (the pillar and the block next to it) backward with two parallel rows of solid blocks as far as you need.

  7. Create the Repeater Delay Loop

    Break the redstone dust adjacent to the sticky piston and replace it with a redstone repeater running away from the input along your new platform. Run a chain of repeaters down one row, bridge the end with redstone dust, and run repeaters back up the second row into the sticky piston.

  8. Adjust the Tick Delay

    Right-click the repeaters in your loop to set their delay ticks. The more repeaters and higher tick delays you add, the longer the output pulse will stay active before the piston cuts off the signal.

How it works

This circuit works by racing a direct redstone signal against a delayed piston cutoff:

  • Signal Split: When you flick the lever, power immediately travels down into the 3-dust trench line, turning on your redstone-lamp or output device.
  • The Cutoff Mechanism: Simultaneously, power travels across the top blocks toward the sticky-piston. Note that redstone dust stepping down into a 1-block hole travels diagonally through the air block above the hole.
  • Cutting the Wire: Once the signal reaches the sticky-piston, it extends and pushes a solid block into the space directly above the trench hole. Solid blocks cut diagonal redstone connections, instantly severing the signal to the output even though the lever remains on.
  • Adjusting Duration: In the basic version, the piston activates almost immediately, creating a very brief pulse. By routing the piston's power line through a loop of redstone-repeater blocks, you delay how long it takes for the piston to extend, keeping the trench wire connected for the exact duration of your repeater delay.

Tips & variations

  • Resetting the Circuit: Because this design uses a lever, you must flick the lever off to retract the sticky piston and reset the block before you can trigger another pulse.
  • Compact Adjustments: You don't always need a massive platform; a single repeater set to 1–4 ticks is enough for most basic timings, while longer chains are great for doors or timed traps.
  • Block Choice: Always use full, solid opaque blocks (like wool, stone, or planks) for the block pushed by the piston. Transparent blocks (like glass or glowstone) will not cut off redstone dust connections.

Frequently asked questions

Why doesn't the redstone signal turn off when the piston pushes the block?
Make sure you are using a full solid block (like wool, cobblestone, or wood planks). Transparent blocks like glass or top slabs will not cut a diagonal redstone dust connection.
How do I make the redstone pulse last longer?
Extend the repeater loop leading into the sticky piston and right-click the repeaters to increase their tick delay. The longer it takes the signal to reach the piston, the longer the output pulse will stay on.
Can I use a button instead of a lever?
Yes! If you use a button, this circuit will shorten the button's default pulse to whatever delay you set on the repeaters, and it will automatically reset itself when the button pops back out.

Components used

More pulse limiter