1-Tick Pulse Limiters

A 1-tick pulse limiter (or monostable circuit) takes a long or continuous redstone signal and shortens it into a single, brief 1-tick pulse. These circuits are essential for precise timings in automated farms, piston feed tapes, and complex redstone contraptions in Minecraft Bedrock Edition. Below are four different designs ranging from classic piston mechanics to completely silent and compact logic.

Pulse CircuitsBeginnerBedrock Edition
1-Tick Pulse Limiters video tutorial

Video: 4 one tick pulse limiters for Bedrock Edition (now 5! Read Comments) by Eggfur

How to build it

  1. Design 1 (Dust-Cut): Place Repeater and Blocks

    Start by placing a redstone repeater facing into a solid block. Leave two empty floor spaces after that block, and place a second solid block at the end.

  2. Design 1: Add the Redstone Dust

    Place two redstone dust on the floor in the gap between your two blocks, and place one more redstone dust directly on top of the second solid block. The dust on top of that block is where you will connect your output device.

  3. Design 1: Add the Cut-Off Piston

    Place a sticky piston facing sideways toward the space just above the second floor dust, and attach a solid block to its face. When you power the first block (before the repeater), the piston will push its block to cut the dust line rushing up to the output block.

  4. Design 2 (Moving Block): Dig and Place Piston

    For a more compact moving-block version, dig a one-block hole in the ground and place a sticky piston inside it facing straight up. Place a solid building block on top of the sticky piston.

  5. Design 2: Add Input Dust and Output Repeater

    Place a piece of redstone dust on the ground right in front of the solid block, and place a redstone repeater on the opposite side facing away from the block. Powering the dust will briefly send power through the block into the repeater before the piston pushes the block upward.

  6. Design 3 (Bell & Observer): Place Input and Bell

    Place a redstone dust on the ground leading into a redstone repeater, and put a bell directly in front of the repeater.

  7. Design 3: Attach the Observer

    Place an observer with its face looking directly at the bell. Connect your output to the back of the observer; it will emit a single 1-tick pulse only when the bell is powered on, ignoring when it turns off.

  8. Design 4 (Silent Comparator): Place Comparator

    For a completely silent design, place a redstone comparator on the ground and interact with it once to turn on its front torch (putting it into subtract mode). Your output device goes directly in front of this comparator.

  9. Design 4: Wire the Side Repeater

    Place a redstone repeater running directly into the side of the comparator. Place redstone dust behind the comparator and connect it to the back of the repeater so both receive your input power at the same time.

How it works

Each of the four designs achieves a 1-tick pulse using a different redstone mechanic:

  • Design 1 (Dust-Cut): The input signal splits. It travels instantaneously through the redstone dust up to the elevated output block while simultaneously powering the repeater and sticky piston. After 1 tick, the piston extends a solid block over the lower dust, physically severing the diagonal redstone connection going up to the elevated block.
  • Design 2 (Moving Block): Powering the input dust powers the solid block it points into. That block immediately powers both the output repeater and the sticky piston buried underneath it. One tick later, the piston pushes the block up and out of the way, cutting power to the repeater.
  • Design 3 (Bell & Observer): Normally, an observer outputs two pulses (one when a block turns on, and one when it turns off). However, bells have an internal data state that only toggles when the bell rings (on the rising edge of a signal). When the redstone turns off, the bell does not ring or change state, so the observer only fires once.
  • Design 4 (Comparator & Repeater): The input signal flows straight into the back of the comparator (Set to Subtract Mode) and immediately outputs a signal. At the exact same time, the signal enters the repeater aiming into the comparator's side. Because the repeater adds a 1-tick delay, the full-strength signal hits the side of the comparator 1 tick later, subtracting the entire signal strength down to 0 and shutting the output off.

Tips & variations

  • Java vs. Bedrock Edition: Design 1 (Dust-Cut) and Design 2 (Moving Block) work in both editions (though on Java, 1-tick pulses cause sticky pistons to drop their blocks). Design 4 (Comparator & Repeater) only produces a 1-tick output on Bedrock Edition due to how Bedrock handles comparator and repeater delays.
  • Make Design 3 Tileable: You can make the Bell and Observer pulse limiter 1-wide tileable by placing a solid block between the repeater and the bell so adjacent redstone lines don't power neighboring bells.
  • Output Placement on Design 1: On the Dust-Cut design, make sure you take your output from the redstone dust sitting on top of the final block. If you place your output device next to the bottom block itself, the floor dust will keep the block continuously powered even after the upper line is cut.
  • Speed & Noise: Choose Design 4 if you want a completely silent circuit with zero moving parts. Avoid Design 3 in timing-critical builds, as the combination of a repeater, bell, and observer adds noticeable startup delay (plus constant bell ringing).

Frequently asked questions

Which 1-tick pulse limiter is completely silent?
Design 4 (the comparator and repeater method) is completely silent because it uses pure redstone logic instead of noisy pistons or ringing bells.
Why doesn't the observer fire twice in the bell design?
A bell only updates its block data when it receives power and rings. When the redstone signal turns off, the bell doesn't ring, so the observer detects no change.
Do these pulse limiters work in Minecraft Java Edition?
The first two piston-based designs work on Java Edition, though sticky pistons behave differently with 1-tick pulses on Java. The comparator-repeater subtract design is exclusive to Bedrock Edition.

Components used

More pulse limiter