Underground Flush 2x2 Elevator

This underground flush 2x2 elevator lets you travel smoothly between the surface and a hidden subterranean base while leaving the ground completely flat when raised. It relies on a compact two-way slime block flying machine and a vertical redstone torch tower that lets you launch or recall the platform from either end.

Piston ContraptionsIntermediateJava Edition
Underground Flush 2x2 Elevator video tutorial

Video: (UPDATED) How To Make an Underground FLUSH 2X2 Elevator!!! (JAVA 1.21+) by

How to build it

  1. Build the Flying Machine Core

    Place two observers on top of each other facing the same horizontal direction (red output dots facing the back). Attach a slime block to the output of the bottom observer, place an upward-facing sticky piston next to that slime block, put a second slime block on top of the piston, and attach a downward-facing sticky piston beside the top slime block (above the top observer).

  2. Add the 2x2 Elevator Platform

    Place two more slime blocks across the top of the machine to form a 2x2 top layer, then cover those four blocks with your chosen floor block (such as polished andesite or grass blocks to blend into the terrain).

  3. Park the Machine Temporarily

    Place an immovable block (like a barrel or obsidian) two blocks above the top of the elevator, then update the bottom observer to send the flying machine up against the stop block so you have room to dig underneath.

  4. Dig the Shaft and Bottom Pit

    Mark the side the observer faces look toward—this side must be your underground entrance. Dig the 2x2 elevator shaft down to your desired base floor level, mark a 2x2 doorway on the observer-face side, and then dig the shaft 5 blocks deeper below that floor level.

  5. Install the Bottom Stop and Trapdoor Trigger

    Floor the bottom of the 5-block pit with immovable blocks. On the entrance wall inside this pit, place a trapdoor at the level where the bottom observer will rest, with two solid blocks and two redstone dust behind it.

  6. Line the Lower Shaft Walls

    Replace any shaft walls around the 5-block pit that touch the slime blocks of the elevator with immovable blocks (such as barrels) so the machine does not snag on the walls when landing.

  7. Wire the Bottom Button

    Place a button on the lower-right side of your 2x2 underground entrance. Place a redstone dust on the block directly beneath the button, attach a redstone torch to the side of that block to invert the signal, and place redstone dust underneath the torch to hold the bottom trapdoor powered.

  8. Run the Redstone Torch Tower Upward

    Starting from the block powered by the button's redstone dust, build a vertical redstone torch tower (alternating solid blocks and redstone torches) all the way up to one block below the surface. Adjust the starting point by one block if needed so the final torch at the top defaults to the OFF state.

  9. Build the Top Stop and Launch Mechanism

    One block below the surface beside the top torch, place redstone dust leading into a block with a redstone torch on its opposite side. Run a 2-tick repeater out of that torch into a solid block, place a dropper next to that block in front of the top observer's stopping position, and mount an upward sticky piston in the middle powered by a line of 3 redstone dust from the torch.

  10. Complete the Flying Machine and Send It Down

    Place a movable solid block into the remaining empty gap inside the flying machine frame, remove your temporary upper stop block, and trigger the top observer with an immovable block to send the elevator down to the bottom floor.

  11. Finish the Shaft Lining

    Once the elevator is at the bottom, place one movable floor block on top of the extended top sticky piston head. Line the remaining 2-wide inner walls of the shaft with immovable blocks (corners can be left as normal blocks), then cover the top redstone compartment so the surface is completely flush.

How it works

This elevator is built around a 2x2 two-way vertical flying machine and two docking stations:

  • Flying Machine Movement: Two vertical sticky pistons push and pull opposing pairs of slime blocks. Depending on which observer (top or bottom) receives a block update first, one piston acts as the pusher and the other pulls the trailing assembly along until it hits an immovable surface.
  • Going Up & Recalling from the Top: Pressing the bottom entrance button pulses the dust below it, briefly turning off the inverter torch and flipping the Oak Trapdoor in front of the bottom observer. The observer detects the trapdoor state change and launches the elevator upward. Simultaneously, the pulse travels up the redstone torch tower, turning off the top redstone torch so the top sticky piston retracts its stop block before the elevator arrives.
  • Going Down from the Top: When the elevator is docked flush at the surface, triggering the top mechanism briefly retracts the top sticky piston (removing the physical block holding the elevator up) while the 2-tick Redstone Repeater powers the solid block next to the Dropper. The dropper clicks in front of the top observer, firing the downward engine after the stop block has cleared the path.

Tips & variations

  • Immovable Blocks: Barrels, obsidian, furnaces, glazed terracotta, or open air must be used on the inner walls where the 4 slime blocks slide. Standard stone or dirt will stick to the slime and jam the machine beyond the 12-block piston push limit.
  • Torch Tower Polarity: The topmost torch in the vertical torch tower must be OFF when at rest so the top inverting torch stays ON and keeps the upper stop piston extended. If your shaft height leaves the top torch ON, shift the bottom connection by one block to add an extra inversion.
  • Java Edition Only: This design relies on Java Edition piston update order and 1-tick sticky piston block-dropping behavior inside the flying machine, so it will not function in Bedrock Edition.
  • Camouflage: Use grass blocks for the top 2x2 platform if building in a plains or forest biome so the elevator blends seamlessly into the ground when parked at the top.

Frequently asked questions

Why does my elevator stop halfway up or down the shaft?
A slime block on the flying machine is touching a regular movable block in the shaft wall. Check all four walls along the shaft and replace any blocks touching the slime sides with barrels, obsidian, or air.
What should I do if the top redstone torch in my tower is turned ON instead of OFF?
Your shaft height has an odd number of torch inversions. Move the bottom torch connection up or over by one block to add one more torch to the tower so the top torch rests in the OFF state.
Does this underground 2x2 elevator work on Minecraft Bedrock Edition?
No. Two-way flying machines that use two opposing sticky pistons without glazed terracotta clutches rely on Java Edition piston mechanics and will move erratically on Bedrock.
Do I need to put items inside the dropper at the top?
No, keep the dropper empty. The observer only needs to detect the dropper's activation state change (the click) to start the flying machine heading downward.

Components used

More elevator