2x2 Flying Machine Elevator

This 2x2 flying machine elevator lets you travel vertically between floors in Minecraft Bedrock while staying completely flush with the floor at both the top and bottom stops. It uses a split slime and honey block flying machine with simple redstone dust and observer stations to trigger upward and downward movement. It is an ideal build for secret underground bases, tall towers, or sleek modern homes.

Piston ContraptionsIntermediateBedrock Edition
2x2 Flying Machine Elevator video tutorial

Video: Minecraft Bedrock: Easy 2x2 FLYING MACHINE Elevator Tutorial! 1.21 by Tomco

How to build it

  1. Dig the Shaft and Mark the Floors

    Clear a 4x5 area for the elevator shaft so the flying machine does not snag on the walls. Your bottom floor level will sit 10 blocks above the very bottom of the pit, centered over a 2x2 elevator footprint; mark your desired top floor level directly above that.

  2. Place the Bottom Stop and Base Piston

    At the bottom of the pit, locate the back-right block of your 2x2 elevator column and place an obsidian block. Place a slime block on top of the obsidian and a regular piston to the right of the slime block.

  3. Build the Lower Observer Drive

    Use temporary blocks two spaces to the left of the slime block to place an observer facing into the slime block, then remove the temporary blocks. Two blocks above the slime block, build out to the left again and place an observer on top of the regular piston with a sticky piston attached, followed by an upward-facing observer and another sticky piston on top.

  4. Construct the Honey Half of the Cabin

    On top of the highest sticky piston, stack 5 honey blocks straight up so the top reaches your ground floor level, then place 1 more honey block forward to form half of the 2x2 platform. Underneath that front honey block, place an observer facing into a regular piston (oriented the same way as the bottom regular piston), and at the back place a downward-facing observer with a sticky piston underneath it.

  5. Construct the Slime Half of the Cabin

    Mirror the pillar next to the honey using 5 slime blocks straight up and 1 slime block forward to complete the 2x2 platform. Skip two blocks down from the top and place an observer underneath facing into a sticky piston next to the existing sticky piston, then attach one solid building block beside it.

  6. Install the Top Floor Stopper Pistons

    Go to your top floor level, place two temporary blocks under the floor edge, and place two regular pistons behind them facing straight down to catch the elevator. Remove the temporary blocks when done.

  7. Wire the Top Call Station

    Build an L-shaped platform of solid blocks two blocks below the downward pistons. Place a sticky piston underneath the corner block with an observer attached facing left, run redstone dust across the top of the L-shape, and place a button on one of the powered blocks.

  8. Build the Bottom Glass Staircase

    At the ground floor, place a block with a button near the front-right corner. Run a staircase of glass blocks down toward the bottom of the flying machine and lay redstone dust down the entire glass path.

  9. Connect the Bottom Trigger and Cap the Elevator

    At the bottom of the glass line, place a downward-facing sticky piston holding an observer that fires into redstone dust leading into the lower piston of the flying machine. Finally, place four floor blocks on top of the 2x2 slime and honey platform and surround the ground-floor opening with non-stick blocks like glazed terracotta or shulker boxes.

How it works

This elevator works by separating a 2x2 platform into two linked halves—one built from slime blocks and one from honey blocks—so adjacent pillars do not stick to each other and exceed the 12-block piston push limit.

  • Sending the Elevator Up: Pressing the bottom button sends a signal down the glass staircase to a sticky piston that pushes an observer into place. The observer pulses the lower piston of the flying machine, starting a chain reaction of observers and sticky pistons that inches the cabin upward until it hits the immovable stopper at the top floor.
  • Sending the Elevator Down: Pressing the top button powers the redstone dust line, extending the upper sticky piston and observer assembly alongside the downward-facing regular pistons. This updates the upper observer on the flying machine, reversing the push-pull cycle until the base of the machine comes to rest on the bottom obsidian block.

Tips & variations

  • Swap Slime and Honey Counts: You need 11 of one stick-block and 6 of the other. If you have more honey than slime, simply swap their roles when building the two sides of the machine.
  • Non-Stick Floor Border: Because exposed slime and honey blocks travel past the ground floor, the blocks directly bordering the 2x2 shaft opening must be non-stick blocks such as glazed terracotta, obsidian, or shulker boxes.
  • Do Not Forget the Platform Cap: You must place four solid blocks on top of the top slime and honey blocks to act as the elevator floor; without them, the flying machine will not stop cleanly and can break.
  • Bedrock Edition Timing: Flying machines rely heavily on piston update order. This two-way layout is specifically tuned for Minecraft Bedrock Edition (1.21+) so it does not randomly reverse direction mid-flight.

Frequently asked questions

Can I use only slime blocks instead of both slime and honey?
No. Slime blocks and honey blocks do not stick to each other, which keeps the two halves of the 2x2 elevator below the 12-block piston push limit. You can swap which side uses 11 and which uses 6, Pass both types are required.
Why does my elevator get stuck passing through the ground floor?
The slime and honey blocks on the sides of the cabin will grab onto regular floor blocks. Replace the blocks directly surrounding the 2x2 shaft opening with non-stick blocks like glazed terracotta, obsidian, or shulker boxes.
Why did my flying machine break when reaching the top floor?
Make sure you placed four regular floor blocks on top of the 2x2 slime and honey platform and installed the two downward-facing regular pistons at the top floor to stop the machine.

Components used

More elevator