
Video: Lossless Item Elevator | Minecraft Bedrock Redstone Tutorial | MCPE XBOX PS by
How to build it
- Design 1 (Extender): Set Up the Dropper Tower
Clear a 3x8 build area and stack your droppers vertically facing upward to your desired height. Attach an input hopper feeding into the back of the bottom-most dropper.
- Design 1: Build the Input Reader
Place a comparator facing away from the bottom dropper. Run it directly into a repeater set to its default 1-tick delay, followed by a single piece of redstone dust.
- Design 1: Add the Pulse Extender
Place a comparator facing away from that dust, then place a second comparator directly next to it facing the opposite direction to form a loop. Put a solid block in front of the returning comparator and connect the ends with three pieces of redstone dust.
- Design 1: Wire the Slow Clock
Next to your very first input comparator, place another comparator facing the same direction into a solid block. Place a repeater next to that block facing back toward the extender, and wire the clock and extender together with redstone dust, using a solid block on the corner so signal strength 1 still powers the loop.
- Design 1: Build the Torch Tower
On top of the solid block next to your clock's comparator and repeater, place a redstone torch. Alternate placing solid blocks and redstone torches straight up alongside the dropper tower until the top dropper is adjacent to a powered block or torch.
- Design 2 (Observer): Dropper & Block Columns
For the compact 3x4 observer design, build your vertical stack of upward-facing droppers and attach the input hopper to the side or back of the bottom dropper. Directly next to the droppers, build a matching vertical column of solid blocks.
- Design 2: Place Horizontal Observers
Along the column of solid blocks, place a vertical line of observers facing away from the blocks so their red output dots point directly into the solid blocks.
- Design 2: Wire the Base Clock
Place a comparator reading the bottom dropper facing away from the tower. Diagonally from the comparator, place a repeater facing back toward the tower, and connect them using two solid blocks and three pieces of redstone dust.
- Design 2: Build the Downward Observer Tower
Starting right above the redstone dust in front of your horizontal observers, stack a vertical line of downward-facing observers all the way to the top. Leave the repeater on 1 tick for silent operation, or set it to 2 ticks for double-speed item transfer.
How it works
Both elevators solve the stuck-item problem by ensuring the upward transfer pulses continue until the final item exits the top dropper:
- Design 1 (Pulse Extender + Torch Tower): When an item enters the bottom dropper, the first comparator reads it and sends a full-strength signal into the two-comparator fade-out loop (pulse extender). This extender keeps the adjacent comparator-repeater clock running well after the bottom dropper empties. The clock rapidly toggles the vertical redstone torch tower on and off, pulsing every dropper in the column until all items are pushed out the top.
- Design 2 (Observer Tower): The comparator detects items in the bottom dropper and powers a feedback loop with the repeater and dust. The front column of downward-facing observers watches the redstone dust turn on and off, sending a vertical chain of pulses up the tower. The second column of horizontal observers detects each pulse and powers the solid blocks next to the droppers, moving the item smoothly upward one level at a time.
Tips & variations
- Scaling Tall Extender Towers: If you build Design 1 very tall, items might stop near the top before the extender runs out. Simply break the end block and dust of the pulse extender, add more pairs of opposing comparators in the middle, and replace the block and dust to increase the run time.
- Redirecting Dust Around Hoppers: In Design 1, if you want your input hopper on the side near the redstone dust instead of the back, replace the adjacent solid block with a Target Block so the dust redirects away from the hopper and doesn't lock it.
- Silent vs. Double Speed (Design 2): Leaving the repeater on a 1-tick delay makes the observer elevator completely silent (only the dropper currently holding an item clicks). Setting the repeater to 2 ticks triggers the observers on both the rising and falling edge of the signal, doubling the speed and flushing out any items that might stall during chunk unloading.
- Input Speed Limits: The comparator-repeater clock is optimized for a single hopper input. Using ultra-fast piston or comparator clocks on a single hopper input causes unnecessary noise and lag without moving items any faster.





