ImpulseSV Overflow-Protected Item Sorter

The ImpulseSV item sorter is the gold standard for organizing items in Minecraft survival bases and mob farm storage rooms. Each 1-wide slice filters one specific stackable item type into its own chest while sending unsorted items further down the hopper line. Unlike older 2-dust designs, this circuit includes built-in overflow protection so a full chest will never break the neighboring filters.

Item CircuitsBeginnerJava Edition
ImpulseSV Overflow-Protected Item Sorter video tutorial

Video: Minecraft - Tutorial: Quick & Easy Item Sorter (With Overflow Protection) by impulseSV

How to build it

  1. Place the Storage Chests

    Place your storage chests in a row. If you are using an older version of Minecraft where regular chests cannot sit side-by-side without merging, alternate between regular chests and trapped chests.

  2. Connect the Bottom Output Hoppers

    Crouch and place one hopper pointing directly into the back (or top) of each storage chest. These hoppers will push filtered items into your chests.

  3. Install the Middle Filter Hoppers

    Place a temporary block above the chests, then crouch and place a row of hoppers above the first row, facing forward into those temporary blocks (or facing into the comparator later so they do not point straight down). Remove the temporary blocks so the chests can open.

  4. Run the Top Feeder Hopper Line

    Above the filter hoppers, run a line of hoppers pointing sideways from your input chest at one end toward an overflow/unsorted chest at the far end.

  5. Place the Comparators

    Behind the middle filter hoppers, place a row of solid blocks one level down. Place a redstone comparator on each block reading out from the middle filter hopper.

  6. Build the 3-Dust Signal Line

    Extend solid blocks out behind each comparator so that each slice has a line of three blocks going backward, plus one block dropped down at the end. Place redstone dust along the top of those three blocks behind every comparator.

  7. Add Repeaters Under the Dust Line

    Underneath the middle block of the 3-dust line, place a solid block with a redstone repeater facing back toward the chests. Place another solid block directly behind the dust line so the dust powers the repeater.

  8. Place the Locking Redstone Torches

    Place a solid block directly in front of each repeater (under the comparator support block) and attach a redstone torch to the front face of that block so it sits right next to the bottom output hopper, locking it.

  9. Configure the Filter Hopper

    Rename 4 stackable items in an anvil per slice so they will never accidentally enter your storage system. Open each middle filter hopper and place 1 named item into each of the right four slots (slots 2, 3, 4, and 5).

  10. Load the Target Item

    Place the item you want that slice to sort into the first (leftmost) slot of the filter hopper. You can put 41 in immediately, or drop at least 1 in and let the system naturally buffer up to 41 as items flow through the top feeder line.

How it works

The circuit relies on precise comparator signal strength and hopper locking mechanics:

  • Idle State (41 + 4 items): With 1 renamed item in each of the last four slots and 41 of the target item in the first slot (45 items total for 64-stackable items), the comparator outputs a signal strength of 2. The signal travels across the first two redstone dust pieces, stopping just short of the third dust. The repeater stays unpowered, the redstone torch stays ON, and the bottom hopper remains locked so the filter never drains.
  • Sorting State (42+ items): When a matching item passes through the top feeder hopper, the middle filter hopper pulls it down into the first slot (now 46 total items). This pushes the comparator output to signal strength 3, reaching the third redstone dust and powering the block behind it.
  • Unlocking the Hopper: That powered block activates the repeater, which powers the block holding the redstone torch. The torch turns OFF briefly, unlocking the bottom hopper just long enough to pull items out until the filter hopper drops back down to 41 target items, turning the torch back on.
  • Overflow Protection: If a chest and its bottom hopper completely fill up, the first slot of the filter hopper can only hold at most 64 items (68 items total in the hopper). A hopper with 68 items only outputs a maximum signal strength of 3. Because strength 3 is only strong enough to reach the slice's own repeater and cannot reach distance 4, the signal never bleeds into the adjacent slice to drain its filter.

Tips & variations

  • Never use unrenamed filter items: Always rename the 4 blocker items in an anvil (e.g., dirt or sticks renamed to "Filter"). If a normal item matching your filler enters the input chest, it can stack into slots 2–5 and break the slice.
  • 64-Stackable items only: Standard filter counts (41 target + 4 filler) are calibrated for items that stack to 64. Items that stack to 16 (like ender pearls or signs) give stronger signal per item, and non-stackable items cannot be sorted with this filter.
  • Chest placement options: You can either stack the hoppers straight above the chests or tuck the bottom hopper into the back of the chest to lower the entire build by 1 block at the cost of 1 extra block of depth.
  • Modern versions note: In newer Minecraft versions (1.13+), regular chests can be placed side-by-side while crouching without merging, so you no longer need to alternate with trapped chests.

Frequently asked questions

Why does the filter hopper stop at 41 items?
With 1 filler item in each of the last 4 slots (4 items) plus 41 items in the first slot (45 total), the comparator emits signal strength 2. As soon as a 42nd item enters (46 total), the signal hits strength 3 and unlocks the bottom hopper until the count returns to 41.
What makes this design overflow-protected compared to older 2-dust sorters?
Because slots 2 through 5 hold only 1 renamed item each, the maximum number of items the filter hopper can ever hold is 68 (64 + 1 + 1 + 1 + 1). That produces a maximum signal strength of 3, which is not strong enough to spill over into neighboring slices and drain their filters.
What happens to items that do not have a filter?
Any item that does not match a filter simply stays in the top feeder hopper line and travels all the way to the chest or disposal system at the end of the row.

Components used

More item sorter