Reliable Bedrock Item Sorter

This 1-wide tileable item sorter for Minecraft Bedrock Edition uses a target block to redirect redstone and invert a torch without needing a repeater or piston. Because it avoids the repeater delay that makes classic Java-style sorters skip items on Bedrock, it reliably filters bulk drops from mob farms, mines, and storage halls while remaining overflow-proof.

Item CircuitsBeginnerBedrock Edition
Reliable Bedrock Item Sorter video tutorial

Video: Minecraft Bedrock: New Item Sorter! Simple, Cheap, Reliable! MCPE Xbox PC Ps4 Switch by silentwisperer

How to build it

  1. Stack the storage chests

    Reserve a 1-wide, 7-block-long, 4-block-tall space per slice and stack three double chests on top of one another at the front. You can add more chests above or below depending on how much storage you need.

  2. Attach the chest hoppers

    Crouch and place three hoppers along the back of the chest column so each hopper points directly into the back of its double chest.

  3. Place the filter hopper

    Place a temporary block behind the top hopper, crouch-place your filter hopper on top of the chest hoppers so its nozzle points into that temporary block (away from the chests and comparator), and then break the temporary block.

  4. Add the comparator

    Place a solid block one block behind the top chest hopper so it sits directly below the filter hopper level, then place a redstone comparator on top of it reading out of the filter hopper.

  5. Build the redstone support blocks

    Place a solid block directly in front of the comparator so the comparator runs into it. Next, place a glass block one block behind and below that solid block, followed by another solid block extending further back at the same height as the glass.

  6. Install the target block and torch

    Place a target block underneath the solid block that the comparator faces into (sitting between the glass and the lower chest hoppers). Attach a redstone torch to the front side of the target block so it sits right behind the middle hopper and locks it.

  7. Lay the three redstone dust

    Place three pieces of redstone dust on top of the solid block in front of the comparator, the glass block, and the rear solid block. The target block automatically redirects the dust line into itself.

  8. Configure the item filter

    Open the filter hopper and put 1 renamed filler item into each of the last four slots (slots 2 through 5), then place a stack of the item you want to sort into the first slot. The hopper will drain down to 41 of your target item and hold there.

  9. Run the top input hopper line

    To tile the sorter, repeat the slice directly alongside the first and run a chain of hoppers across the top of the filter hoppers leading from an input chest at one end to an overflow chest at the other.

How it works

This sorter relies on signal strength and the 1.17+ Bedrock mechanic where a target block both conducts redstone power and redirects adjacent redstone dust into itself.

  • Idle state (45 items): With 41 target items in slot 1 and 4 renamed filler items in slots 2–5, the redstone-comparator outputs signal strength 2. That powers only the first two pieces of redstone-dust and does not reach the dust adjacent to the target block, so the redstone-torch stays ON and locks the hopper below the filter hopper.
  • Sorting state (46+ items): When a matching item enters the filter hopper from the top input line, the total rises to 46 items and the comparator outputs signal strength 3. All three dust power up, energizing the rear solid block and the redirected dust going into the target block.
  • Soft inversion: Powering the target block turns OFF the attached redstone torch for just long enough to unlock the middle hopper, pulling one matching item down into the storage chests until the filter hopper drops back to 41 items in the first slot.
  • Overflow protection: Because each slice uses three dust, even if a chest column fills completely and slot 1 reaches 64 items, the comparator never exceeds signal strength 3 and will not bleed into adjacent slices.

Tips & variations

  • Why no repeater? The classic Java ImpulseSV sorter uses a repeater at the back, which adds extra delay on Bedrock Edition and causes items to occasionally slip past into the overflow chest. Replacing the repeater/piston with a target block removes that delay and makes the slice completely silent.
  • Always rename filler items: Use an anvil to give your four filler items a custom name so stray items passing through the input line can never stack into slots 2–5 and break the filter.
  • Valuable-item variant (2-dust): If you do not want to leave 41 diamonds or wither skulls stuck in the filter, build the shorter 2-dust variant using an upper slab to step the dust down into the target block. Fill the filter hopper with 2 target items in slot 1 and 5 renamed filler items in each of the remaining four slots. Note that this variant is not overflow-proof if the chest ever fills completely.
  • Non-stackable item sorter: You can raise a slice up by one block and leave the filter hopper completely empty; stackable items only emit signal strength 1 and pass over, while unstackable items (tools, armor, potions) emit signal strength 3 and drop straight into the chest.

Frequently asked questions

Why does this Bedrock item sorter use a target block instead of a repeater?
On Minecraft Bedrock Edition, the repeater in the classic ImpulseSV sorter introduces extra delay that makes items randomly skip their filter. A target block redirects the redstone dust and soft-inverts the torch without a repeater or noisy piston.
Is this item sorter overflow-proof?
Yes. The 3-dust version holds 41 filter items plus 4 renamed filler items, so even if the chests back up and the first slot hits 64 items, the signal strength stays at 3 and cannot unlock neighboring slices.
How do I sort rare items without locking 41 of them in the hopper?
Use the 2-dust variant with 2 valuable items in the first slot and 5 renamed filler items in each of the other four slots (20 filler items total). It only keeps 2 valuables in the filter, though it is not overflow-proof if the storage chests completely fill up.

Components used

More item sorter