Simple 4x4 Piston Door

A 4x4 piston door creates a grand entrance for your base without requiring complex double piston extenders everywhere. This beginner-friendly Bedrock Edition design uses slime and honey blocks alongside a smart sand-and-torch column to open and close a 16-block doorway cleanly inside a 10x9x2 footprint.

Piston DoorsBeginnerBedrock Edition
Simple 4x4 Piston Door video tutorial

Video: The SIMPLEST 4x4 Door! [Minecraft Bedrock 1.21] Tutorial by Tomco

How to build it

  1. Build the Frame and Sticky Piston Layout

    Clear a 10-block long, 2-block wide, and 9-block tall area. Build your 4x4 door frame and position the sticky pistons around the perimeter—bottom, top, and sides—facing inward toward the doorway opening. Remember which side is the front, as the back side will show the exposed slime and honey blocks.

  2. Wire the Bottom Input and Torches

    At the bottom center beneath the lower sticky pistons, place two solid blocks with redstone dust on top of both. Attach a redstone torch to the outer sides of those two blocks, and place a lever on the front to act as your main input.

  3. Build the Lower Side Torch Towers

    On the left side, leave a one-block gap from the bottom torch, then place two blocks with redstone dust on top (the dust should power on). Place a solid block directly above the bottom redstone torch, attach another redstone torch to it, and step up with two more blocks topped with redstone dust.

  4. Add Non-Sticky Block Stoppers and Mirror

    Place two obsidian blocks (or glazed terracotta) adjacent to the upper redstone dust to keep the upcoming slime blocks from grabbing the frame. Mirror this exact torch tower, dust line, and obsidian setup on the right side of the door.

  5. Place the Slime and Honey Columns

    On the back of the side pistons, place a vertical column of 4 slime blocks on the left side and a vertical column of 4 honey blocks on the right side. Using one of each prevents the two halves of the door from sticking together in the middle.

  6. Fill in the 4x4 Door Blocks

    Using your chosen solid door blocks, place 4 blocks across the bottom pistons, 4 along the left wall, 4 across the ceiling pistons, and 4 along the right wall. Then move to the front face and attach two vertical pairs of door blocks onto the inner faces of the slime and honey columns.

  7. Install the Sand Column Power Switch

    On one side above the torch tower, place a regular upward-facing piston with 2 sand blocks stacked on top of it. Behind the bottom sand block, place a redstone torch, and on the opposite side of that sand block, place a redstone repeater facing outward into a solid block with redstone dust on top.

  8. Wire the Top Pistons

    Place two obsidian blocks on both the left and right upper corners to protect the wiring from the slime and honey. Run a line of solid blocks and redstone dust from the sand repeater output up and across the top sticky pistons so they fire in sync with the rest of the door.

How it works

This 4x4 door avoids complicated double-piston extender wiring by splitting the 16 door blocks between outer frame pistons and two central 4-block vertical strips made of slime blocks and honey blocks.

  • Bottom & Side Inversion: Flipping the bottom lever powers the central dust, turning off the two bottom redstone-torch blocks. This inverses the side torch towers and retracts or extends the bottom and side sticky-piston groups simultaneously.
  • Slime & Honey Separation: Because slime blocks and honey blocks do not stick to one another, the left and right center columns can slide past each other cleanly without locking up, while pulling the inner 2x4 door blocks along with them.
  • Sand Column Relay: An upward-facing regular piston pushes a 2-high stack of sand. When raised, a redstone-torch powers through the bottom sand block into a redstone-repeater, sending the signal all the way to the top row of sticky pistons at the right timing.

Tips & variations

  • Decorating the Tunnel: Any block touching the moving slime or honey columns must be unmovable or non-sticky. Use obsidian, glazed terracotta, or shulker boxes for the hallway walls and ceiling immediately behind the door.
  • Moving the Lever: To control the door from further away, run your external redstone dust line directly into the two bottom-center dust blocks beneath the floor pistons.
  • Bedrock Exclusive: This layout relies on Minecraft Bedrock piston timing and redstone dust connectivity over torches; it will not work properly in Java Edition due to quasi-connectivity.

Frequently asked questions

Can I use all slime blocks instead of mixing slime and honey?
No. The center columns touch each other when the door closes. If both sides use slime blocks, they will stick together and exceed the 12-block piston push limit.
What can I use instead of obsidian if I am building in early survival?
You can substitute obsidian with glazed terracotta, furnaces, barrels, or chests—any block that does not stick to slime and honey or cannot be pushed by pistons.
Does this 4x4 door work on consoles and mobile?
Yes, it works on all Minecraft Bedrock platforms including Xbox, PlayStation, Nintendo Switch, iOS, Android, and Windows.

Components used

More 4x4 door