Simple 2x2 Flush Piston Door

A 2x2 flush piston door, widely known as a Jeb Door, hides an entrance completely flat against a wall so nobody can tell a door is there. When toggled, the wall blocks pull back and slide aside to reveal a secret 2x2 hallway. It is one of the best beginner-friendly redstone builds for hiding secret bases and valuables in survival Minecraft.

Piston DoorsBeginnerJava Edition
Simple 2x2 Flush Piston Door video tutorial

Video: Simple Minecraft 2x2 Flush Piston Door. 1.26 Redstone Tutorial by Sassyfish

How to build it

  1. Place the 12 sticky pistons

    Behind where your wall will be, place a 2x2 grid of sticky pistons on the left facing inward toward the center hallway, and a matching 2x2 grid on the right facing inward (leave a 4-block gap between them). In front of the inner faces of those pistons, place two vertical columns of two sticky pistons facing forward toward the wall.

  2. Add the door blocks

    Attach four building blocks (matching your wall material, such as calcite or stone) onto the faces of the four forward-facing sticky pistons.

  3. Power the side pistons with torches

    Behind the back-outer sticky pistons on both the left and right sides, place a circuit block on the ground with a redstone torch on it, then place another circuit block directly on top of that torch. Both side piston arrays will immediately extend inward, pushing the front pistons and door blocks into the center.

  4. Build the top wiring platform

    Place circuit blocks directly on top of the four forward-facing sticky pistons (in their pushed-in central position) and add an L-shaped arrangement of blocks just behind them to hold the top redstone.

  5. Add the top inverter and repeaters

    Place a redstone torch on the back of the top structure with redstone dust in front of it so the four front pistons extend and push your door blocks flush into the wall. Place repeaters feeding into the top piston blocks and set them to 3 ticks (or 2 ticks if you do not use an extra line repeater later).

  6. Connect both side torch towers

    Run a redstone dust line from the top torch block down both sides to connect into the blocks holding the side redstone torches. Place a 1-tick repeater along the side line if needed to keep the signal strong.

  7. Wire the hidden lever underground

    Route the main redstone input line down underground and underneath your wall to a spot where you want your switch. Place a lever on the wall block above the wire—flip it to open and close your flush door, or remove the lever when you leave so nobody can find the entrance.

How it works

This flush door uses redstone torches as inverters (NOT gates) so the door stays closed and completely flush with the wall by default:

  • Default (Closed) State: With the lever off, all redstone torches stay lit. The side torches power both the bottom and top side sticky pistons (through the block above each torch), pushing the front sticky pistons into the doorway. At the same time, the delayed top circuit powers the front pistons from above, pushing the four wall blocks forward so they sit completely flush with the wall.
  • Opening Sequence: Flipping the lever sends power into the blocks holding the redstone torches, turning them off. Because the top repeaters are set to a longer delay (2 ticks slower than the front retraction), the front sticky pistons unpower first and pull the wall blocks back one block. Two ticks later, the side pistons unpower and pull both the front pistons and the wall blocks cleanly to the left and right sides.
  • Closing Sequence: Turning the lever off allows the side torches to relight first, pushing the front pistons back to the center before the delayed signal reaches the top pistons to push the wall blocks forward again.

Tips & variations

  • Java Edition Exclusivity: This classic overhead wiring design relies on quasi-connectivity (QC) to power the bottom middle pistons from the blocks above the top pistons. It works reliably in Minecraft Java Edition, but the bottom two blocks will not push forward in Bedrock Edition without rewiring the bottom pistons directly.
  • Repeater Timing Rule: The side pistons must always react 2 ticks after the front circuit when opening. If you add a 1-tick repeater on the main line to boost signal strength from a distant lever, set the top repeaters to 3 ticks. If you don't use an extra repeater on the line, set the top repeaters to 2 ticks.
  • True Secret Entrance: Memorize the exact wall block your underground redstone line reaches, and break your lever after closing the door. Keep a lever in your inventory and place it on that spot whenever you want to enter.

Frequently asked questions

What is a Jeb Door in Minecraft?
A Jeb Door is a 2x2 flush piston door that uses 12 sticky pistons to pull a 2x2 section of wall backward and then split it left and right, leaving a completely flat, undetectable wall when closed.
Why are my front door blocks getting stuck instead of pulling into the sides?
Your repeater delay is off. The front sticky pistons must retract before the side sticky pistons pull them sideways. Increase the delay on the repeaters controlling the side/top circuit to 2 or 3 ticks.
How do I keep other players from seeing the lever?
Run the redstone dust wire underneath the wall and place the lever on a normal wall block above it. Once you close the door, break the lever and carry it with you so the wall looks completely untouched.

Components used

More 2x2 door