4x4 Vault Piston Door

A 4x4 vault door creates a dramatic, recessed entrance for large bases and underground vaults while avoiding complex triple piston extenders. This supercharged slime-block design opens at lightning speed, fits within a 3-block deep footprint, and looks completely identical from both the front and back with zero exposed pistons.

Piston DoorsIntermediateJava Edition
4x4 Vault Piston Door video tutorial

Video: Minecraft: Supercharged 4x4 Vault Door [New Design!] by Mumbo Jumbo

How to build it

  1. Lay the Bottom Redstone Line

    Clear a 3x12 building area. Starting four blocks in from the 12-block edge, place a centered row of 4 solid blocks along the middle with redstone dust on top of each, then attach redstone torches to both the front and back sides of all 4 blocks (8 torches total).

  2. Install the Bottom Pistons and Floor

    Place 8 upward-facing sticky pistons directly on top of the 8 redstone torches, and put solid door blocks on top of every piston face. Place 4 solid blocks directly above the middle redstone dust line to form the central floor walkway.

  3. Set Up the Side Slime Piston Assemblies

    On both the left and right sides of the doorway frame, place an immovable block (such as obsidian or a furnace) in the middle row just outside the floor, then stack two regular door blocks on top of it and two slime blocks behind those in the center. Place 2 inward-facing sticky pistons outside the slime blocks, and flank them with 2 inward-facing regular pistons on both the front and back layers.

  4. Build the Central Torch Towers

    Extend the bottom redstone dust line outward by one block on both ends, stepping up into a block with a redstone torch on top, and cap that torch with a solid immovable block (obsidian or furnace). From the side of that block, build a vertical torch tower going up using 3 redstone torches and 3 solid blocks alternating upward.

  5. Wire the Four 2-Tick Side Branches

    On all four corners of the bottom redstone line, pull the signal onto an upside-down slab with redstone dust on top. Run each slab into a repeater set to 2 ticks facing a solid block, then build a short torch tower up the side using a side torch, a block above it, a torch on top, and a final solid block on top.

  6. Test and Fill the Side Door Blocks

    Attach a lever connected to the bottom redstone line and flick it ON so the side sticky pistons push the slime blocks inward. Place solid door blocks directly onto the faces of the 8 regular pistons on the front and back so the slime blocks can grab and retract them.

  7. Frame the Top Doorway and Pistons

    Place immovable blocks on the upper inner corners above the slime block assemblies to prevent sticking, then bridge across the top to complete the 4x4 doorway frame. Above the ceiling frame, install two rows of 4 downward-facing sticky pistons on the front and back layers (8 total) with door blocks attached to their faces.

  8. Wire the Top Piston Roof

    On both the left and right top corners, place redstone dust above the top torch of the central tower and route it up a staircase of 5 upside-down slabs lined with redstone dust. Run each side into a 1-tick repeater facing a solid block, with redstone dust and an adjacent block positioned between the top sticky pistons to power all 4 pistons per side.

How it works

This circuit coordinates 28 pistons around a 4x4 frame using a single bottom input line split into synchronized vertical towers:

  • Bottom Double Layer: The central line of 4 redstone dust powers the blocks beneath the floor. When the lever is OFF, the 8 attached redstone torches stay lit, holding the two bottom rows of 4 sticky pistons extended. Turning the lever ON inverts the torches and immediately drops the bottom row flush with the floor.
  • Slime Block Center Mechanism: Instead of using bulky double piston extenders to pull the middle 2x2 blocks, each side uses a pair of sticky pistons in the center layer to push and pull two slime blocks. However, because the outer frame must look flush on both sides, 8 regular pistons sit on the front and back layers. During closing, a 2-tick repeater branch fires the regular pistons to push the outer door blocks into place after the slime blocks extend. During opening, the central torch tower retracts the sticky pistons and slime blocks, pulling the center and outer door blocks back simultaneously.
  • Immovable Block Stops: Obsidian or furnaces are placed adjacent to the path of the slime blocks so the slime only grabs the intended door blocks without tearing apart the surrounding doorway frame or torch towers.
  • Top Double Layer: The central torch towers continue all the way to the roof via upside-down slab ladders. A 1-tick repeater powers a central block and redstone dust on each half of the roof, powering the 8 downward-facing sticky pistons via direct power and quasi-connectivity.

Tips & variations

  • Immovable Block Choices: The blocks touching the slime path must not be movable by pistons. Use obsidian, furnaces, dispensers, droppers, or note blocks. Note that the immovable block placed directly above a redstone torch in the central tower must be a solid opaque block (like obsidian or a furnace) so it can transmit power to the torch attached to its side.
  • Symmetrical Appearance: Unlike older vault doors that leave ugly piston heads exposed on the back side, this 3-wide layout mirrors the front and back layers around a central slime core so both faces of the hallway look identical.
  • Java Edition Only: This design relies on Java Edition piston update timing, 1-tick/2-tick slime block swap timing, and quasi-connectivity for the upper and side piston columns. It will not function properly on Bedrock Edition.
  • Common Mistake: Make sure to flick the lever ON before placing the door blocks in front of the 8 regular side pistons during construction; placing them while the door is closed will result in blocks being out of sync with the slime blocks.

Frequently asked questions

Why does the door use both regular pistons and sticky pistons on the sides?
The center sticky pistons move the slime blocks, which pull the outer door blocks open. Regular pistons are used on the front and back layers to push those outer blocks flush into the doorway when closing without sticking to them when the slime blocks retract.
What can I use instead of obsidian in Survival mode?
Furnaces, droppers, or dispensers work just as well as obsidian because they cannot be moved by slime blocks and are solid blocks that can conduct redstone signals and hold redstone torches.
How deep is this 4x4 vault door?
The entire mechanism is only 3 blocks deep (12 blocks wide by 3 blocks deep), and both the front and back faces look completely symmetrical.

Components used

More vault door