10x10 Sliding Piston Door

This 10x10 sliding piston door uses twenty horizontal flying machines—ten on each side—that meet in the middle to close a massive entrance. Because it opens sideways rather than vertically, you don't have to excavate a deep pit below your floor, making it ideal for giant hangar doors, vaults, or mega-bases.

Piston DoorsAdvancedJava Edition
10x10 Sliding Piston Door video tutorial

Video: 10x10 Sliding Piston Door - Minecraft Redstone Tutorial 1.18+ by Monocle

How to build it

  1. Clear a 40x5 Footprint

    Prepare a flat area that is 40 blocks wide and 5 blocks deep. Because the door slides open sideways, you only need a two-block-deep trench in the floor later for the button wiring.

  2. Place the Outer Trigger Piston & Backstop

    Go to the right corner of your build area and place a regular piston facing inward toward the door, with a solid block, a glass block, and redstone dust behind it. Place an obsidian block beside it to act as the outer backstop, and set an observer against that obsidian facing into the flying machine area.

  3. Build the First Flying Machine Drive

    Against the observer, attach a sticky piston pushing two slime blocks, followed by an inward-facing sticky piston and two honey blocks. Add two more slime blocks, two observers watching the pistons, an iron block with two slime blocks forming a small L-shape, and a third sticky piston.

  4. Attach the First 5-Block Door Row

    In front of the third sticky piston, place a 2-block honey connector followed by a row of 5 honey blocks. Attach 5 iron blocks (your actual door surface) to the front of those honey blocks, and place a temporary obsidian stop-block at the center line of the doorway for testing.

  5. Build the Inner Return Trigger

    At the point where the flying machine stops when closed, place a regular piston above the observer line with a yellow wool block one block over. Build a monostable pulse circuit using a sticky piston pushing an observer, a repeater feeding into the block, and redstone dust climbing onto glass to power the return trigger piston.

  6. Test the First Row & Link the Triggers

    Power the outer trigger piston to send the first row across to the center stop-block, confirming the exact spot for the inner return piston. Connect both the outer and inner trigger circuits with a redstone dust line and a repeater so a single button press toggles the machine back and forth.

  7. Mirror the Mechanism on the Left Side

    Go to the opposite end of the 40-block area and build the exact same outer trigger, flying machine, and inner return circuit facing the center. Swap every slime block for a honey block (and vice versa) on this bottom left row so that when the left and right halves meet in the center, their slime and honey rows do not stick to each other.

  8. Connect Both Sides Under the Floor

    Dig a 2-block-deep trench running from your main activation button to the outer corners of both the left and right mechanisms. Run redstone dust down both trenches with repeaters placed along the lines to refresh the signal, then cover the floor back up.

  9. Stack the Trigger Pistons & Glass Towers

    Extend both the outer and inner regular trigger pistons vertically until each column is 10 pistons tall, and extend the outer obsidian backstops to 10 blocks tall. Place alternating glass blocks in a checkerboard zigzag up the backs of all four 10-piston columns and snake redstone dust all the way to the top.

  10. Stack the Remaining 9 Flying Machine Rows

    Build 9 more flying machine rows directly on top of your first row on both the left and right sides to complete the 10x10 door face. Alternate honey and slime blocks on every vertical layer, and always make sure the left side uses the opposite sticky block from the right side on the same layer.

  11. Frame the Doorway Safely

    Build your surrounding walls one block outward from the moving slime and honey wings, or line any touching surfaces with obsidian or other immovable blocks. If you want a button on the inside of the door as well, tap a second redstone line with a repeater into your underground trigger line.

How it works

This door breaks a giant 10x10 wall into twenty independent 5-block horizontal rows—ten sliding in from the left and ten from the right:

  • Trigger Towers: Pressing the button sends a redstone signal underground to both ends of the door. At each end, the signal travels up a 10-block glass redstone tower, firing a vertical column of 10 regular pistons at the same time.
  • Three-Piston Flying Machines: Each regular trigger piston updates an observer at the back of its flying machine layer. The chain of observers and three sticky pistons inches the 5-block door segment forward until the two halves collide in the middle of the 10-wide doorway and stop each other.
  • Return Pulse Circuit: When you press the button again to open the door, a sticky piston and observer monostable circuit sends a 1-tick pulse up the inner glass tower. Those 10 inner regular pistons update the inner observers on every layer, reversing the flying machines until they hit the outer obsidian backstops.
  • Honey & Slime Alternation: Because slime blocks do not stick to honey blocks, alternating each vertical row between honey and slime allows all 10 layers to slide independently without exceeding the 12-block piston push limit. Inverting the pattern between the left and right sides keeps the two halves from welding together at the center seam.

Tips & variations

  • Disable OptiFine / Rendering Mods if Glitchy: The creator notes that OptiFine can cause severe visual stuttering when dozens of slime and honey blocks move at once; vanilla rendering displays the sliding animation much more smoothly.
  • Make a World Backup Before Testing: With 140 slime and honey blocks, a single misplaced block or forgotten obsidian backstop can cause the flying machines to eat the surrounding circuitry. Always copy your world or test in creative first.
  • Keep Walls Clear of Slime & Honey: Leave a 1-block air gap above the top row and along the side pockets where the door retracts. Any regular blocks touching the exposed slime or honey will grab onto the flying machine and jam that row.
  • Repeater Timing on the Underground Line: Try to use the same number of repeaters going to the left and right towers so both halves of the door launch on the exact same tick and meet cleanly in the center.

Frequently asked questions

Why are some rows of my 10x10 door sticking together or jamming?
Two adjacent rows are either using the same sticky block (two slime rows or two honey rows touching vertically or across the center seam), or a moving slime/honey block is brushing against a movable wall or floor block.
Do I have to use iron blocks for the door face?
No, you can replace the 120 iron blocks with any solid, movable building block you like to match your base aesthetic.
Why build a sliding 10x10 door instead of a vertical one?
A sideways sliding door stores its mechanisms to the left and right of the doorway, so you only need to dig 2 blocks into the floor for the button wire instead of excavating a massive pit below your base.

Components used

More bigger doors