
Video: Minecraft Tutorial. Redstone Daylight Clock by Frilioth
How to build it
- Clear the Build Area
Reserve an area that is 9 blocks wide by 4 blocks deep for the main clock face, plus an extra 4x3 space behind it for the afternoon indicator mechanism.
- Build the Lamp Circle
At the front of your build area, count 4 blocks in from the side and place the bottom redstone lamp. Arrange 14 redstone lamps in a vertical circle to form the outer ring of the clock face, and place the 15th lamp in the exact center.
- Place Power Blocks Behind the Lamps
Go behind the clock face and place solid building blocks directly behind every outer redstone lamp except the two lamps on the far left and far right sides. For those two side lamps, place the solid blocks against their outer sides instead (these two blocks will be visible from the front, so match your wall material).
- Add the Repeater Platforms
Behind and one block lower than each power block you just placed, add support blocks to hold your repeaters. On the left and right sides, extend the platforms by two blocks so they have room for both a repeater and a comparator.
- Install the Lamp Repeaters
Place a redstone repeater on each support block, facing directly into the solid blocks that touch the outer ring of redstone lamps.
- Build the Signal Ladder
Behind the repeaters, build a stepped loop of blocks that follows the circle around the back of the clock. Use a top slab on the rising side so the redstone signal can travel uphill without being cut off.
- Lay Redstone Dust and Side Comparators
Place redstone dust along the entire stepped loop behind the repeaters. On the two side platforms, place a comparator feeding into the side repeaters, and extend a small two-block platform with another comparator and dust to carry the signal downhill without losing the required strength setting.
- Place the Daylight Detector
Place your daylight detector at the start of the redstone dust line (near the dawn end of the circle) so its signal feeds directly into the loop.
- Build the Night Reset Piston
From the daylight detector, run a dust dot into a repeater pointing into a solid block with a redstone torch on top. Above that torch area, place a standard piston facing horizontally with a Block of Redstone in front of it so that when night falls (signal strength 0), the torch turns on and pushes the redstone block away.
- Build the Midday Trigger Piston
At the top end of the clock's dust loop (where signal strength 15 reaches at noon), place a repeater leading into a couple of blocks with redstone dust and your second standard piston facing back toward the first piston.
- Connect the Center Afternoon Lamp
Build a line of blocks with redstone dust leading from the midday position of the Block of Redstone straight into the center redstone lamp on the clock face. Decorate the front frame around the lamps with your chosen building blocks.
How it works
This clock translates the analog output of a Daylight Detector (signal strengths 0 to 15) into a visual dial:
- Morning Progression: As the sun rises, the daylight detector's signal strength increases from 1 up to 15. The signal travels along the redstone dust loop around the back of the clock, decaying by 1 for each block traveled. Each Redstone Repeater taps off the line and powers its lamp as soon as the signal reaches that point.
- Comparators on the Sides: Because the wiring has to step up and down around the circle, Redstone Comparators in maintain mode preserve the exact signal strength needed to keep the progression sequential around the bends.
- Afternoon Latch (RS NOR Piston Memory): Since a signal strength of 10 looks identical at 9:00 AM and 3:00 PM, the two Pistons and the Block of Redstone act as a memory cell. When the signal finally hits 15 at midday (around 6,000 ticks), the final repeater powers the second piston, pushing the redstone block over the dust line that lights the center lamp.
- Nighttime Reset: During the afternoon, the outer lamps turn off one by one as the sun sets, while the center lamp stays lit. Once night falls and the daylight detector drops to 0 output, the repeater at the start turns off, allowing the Redstone Torch to turn back on and push the redstone block back to the morning position.
Tips & variations
- Weather Effects: Rain and thunderstorms darken the sky and reduce the daylight detector's peak output by 2–3 levels. If it starts raining right before noon, the signal may not reach 15 and the afternoon center light won't trigger that day.
- Chunk Unloading: Because the afternoon indicator relies on a piston latch triggered at noon and reset at night, leaving the chunks unloaded during noon or midnight (such as going to the Nether or exploring far away) can leave the center light out of sync until the next full cycle completes.
- No Sky Access Destroyed: Make sure the block column directly above the daylight detector has clear access to the sky (or only transparent glass above it), otherwise its signal strength will be capped.




