
Video: 2 Daylight Sensor Lavafall Designs Bedrock Edition by SkyGuyJedi
How to build it
- Design 1: Dig the Obsidian Base Trench
Dig three parallel 3-block-long trenches in the ground, leaving a 1-block space between each trench. Fill those three trenches with an immovable block like obsidian so the slime blocks will not grab the floor.
- Build the Front Pillars and Slime Columns
Above the gaps between the obsidian trenches, build four pillars of solid building blocks 5 blocks tall. Behind the three spaces between your pillars, build three vertical columns of 5 slime blocks each (15 slime blocks total).
- Add the Rear E-Frame and Sticky Pistons
Go behind the slime columns and locate the middle (third) row from the bottom. Place two blocks extending backward from each of the three columns and connect their back ends so the frame looks like a sideways E, then replace the blocks directly touching the middle slime blocks with 3 sticky pistons facing forward.
- Wire the Inverted Night Sensor
Extend a small platform behind the middle of the E-frame and place a redstone torch on the side of a block with redstone dust behind it. Place a daylight detector on top of the block, switch it to night mode, and run redstone dust along the back frame to power all three sticky pistons.
- Fill the Moving Wall and Frame with Stairs
With the pistons extended, place five solid building blocks on the front face of each of the three slime columns to complete the flush wall. Wrap normal stairs around the bottom base of the structure and upside-down stairs around the top rim.
- Place Top Obsidian Guards and Lava
Retract the wall so it is open, then place four obsidian blocks along the very top behind the front pillars (every other block) so the upper slime blocks cannot stick to the ceiling frame. Pour four lava buckets directly against those top obsidian blocks, then switch the daylight sensor back to night mode so the wall stays closed during the day and opens at night.
- Design 2: Build the 3x3 Stair Base and Top
For the second compact design, place stairs facing outward in a 3x3 ring on the ground, leaving a hollow 1x1 gap in the center. Build a 5-block-tall pillar to set the height, remove the bottom 4 blocks, and wrap upside-down stairs in a matching 3x3 ring at the top.
- Install the Stacked Dispensers and Pillar
Break out the center of the top ring and place two dispensers on the back wall facing inward, stacked one on top of the other. Fill the central pillar underneath with decorative blocks like magma blocks, close up the back wall with solid blocks, and wrap stairs around the top.
- Add the Sensor and Load the Buckets
Place a daylight detector behind the top of the pillar, set it to night mode, and place a single piece of redstone dust on top of the upper dispenser. Put a lava bucket inside the top dispenser, an empty bucket inside the bottom dispenser, and manually pour water directly in front of the bottom dispenser face to finish.
How it works
Design 1 (Retractable Slime Wall): Each sticky piston pushes and pulls a 5-tall column of slime blocks along with 5 decorative wall blocks attached to the front (10 blocks moved per piston, staying under the 12-block push limit). Obsidian is placed in the floor trenches and at the top lava source positions so the moving slime columns do not snag on the surrounding frame. The daylight detector is set to night mode and inverted with a redstone torch: during the day, the torch stays ON and keeps the wall pushed forward to block the lava; at night, the sensor turns on, turning the torch OFF and retracting the wall to reveal the four lava streams.
Design 2 (Lava/Water Dispenser Switcher): A night-mode daylight detector sits next to a single piece of redstone dust on top of two vertically stacked dispensers. When night arrives, the sensor powers the dust, simultaneously activating both the top and bottom dispensers. Because the bottom face starts with water placed in front of it and holds an empty bucket, the bottom dispenser sucks up the water while the top dispenser dispenses its lava bucket. It takes a full day-night cycle to toggle again: on the next night trigger, both dispensers fire once more, pulling the lava back in and dispensing the water.
Tips & variations
- Immovable Blocks: In Design 1, you must use obsidian (or another immovable block like glazed terracotta) in the floor trenches and at the top ceiling joints; otherwise the slime columns will lock up past the 12-block piston push limit.
- Full-Cycle Toggle on Design 2: Because dispensers only toggle buckets on a rising redstone edge, Design 2 keeps lava flowing for one full day-night cycle and then switches back to water on the following night.
- Cliffside Integration: Design 1 has exposed redstone wiring in the back, making it ideal to recess into a mountain wall or cliffside base entrance.




