Multi-Input Multi-Output Single Redstone Line

Running separate wires for multiple inputs over long distances wastes space and resources. This circuit encodes up to 15 different inputs into varying signal strengths along a single redstone line, then uses a signal-strength decoder at the destination to trigger the exact corresponding output.

Signal TransmissionIntermediateBedrock Edition
Multi-Input Multi-Output Single Redstone Line video tutorial

Video: One Redstone Line Multiple Inputs & Outputs | Let's Learn Redstone 06 | Minecraft Redstone Tutorial by

How to build it

  1. Place the Input Repeaters

    Line up your input blocks ( up to 15) in a row and place a redstone repeater coming out of each one. Run a connected line of redstone dust directly across the front of all these repeaters, and extend the main output wire out from one end of this row.

  2. Mark the Weakest Input

    Find the input repeater farthest away from where your single output wire leaves the array. Place a temporary lever on this weakest input and flick it on so you can easily see where its signal strength of 1 dies out without having to count blocks.

  3. Extend the Signal to Your Destination

    Follow the active redstone dust until it reaches its very last powered piece (signal strength 1). From that exact spot, carry the preserved signal strength to your output location by alternating solid blocks, comparators, and single dots of redstone dust.

  4. Position the Decoder Input Line

    Guide your comparator extension so that the signal strength of 1 lands on a block positioned four blocks behind your first desired output (the one corresponding to your weakest input). From this block, run a straight line of redstone dust across the back of all your remaining output positions.

  5. Build the Lower Decoder Row

    Facing toward your outputs, place a 1-tick redstone repeater coming out of each block in the decoder dust line. Place a solid block in front of each repeater, and attach a redstone torch to the front side of each of those blocks.

  6. Add the Upper Cancel Row

    Crouch and place a solid block directly on top of each 1-tick repeater from the previous step. Place redstone dust on top of these new blocks, then place a second row of repeaters in front of them (above the solid blocks) and set each of these top repeaters to a 2-tick delay (click once).

  7. Install the Output Torches

    Place a solid block directly in front of each 2-tick repeater, which puts them right on top of the lower redstone torches. Attach a redstone torch to the front of these top blocks; these top torches will stay off by default and act as your individual outputs.

  8. Connect Outputs and Test

    Connect your mechanisms—such as solid blocks topped with redstone lamps—above or in front of the top row of output torches. Replace the temporary lever at the start with a button and test each input to verify it triggers only its matching output.

How it works

This system is divided into three main stages: the Encoder, the Transmission Line, and the Decoder.

  • Encoding Signal Strength: Every repeater outputs a full signal strength of 15. Because the input repeaters are lined up side-by-side feeding into one shared dust line, signals from repeaters farther down the row have to travel through more dust before exiting. Each block of travel reduces the signal strength by 1, giving every button a unique strength on the main wire.
  • Signal Preservation: Standard repeaters reset any signal back to 15, which would erase our encoded data. Instead, the transmission line uses redstone-comparator chains (or carefully spaced repeater arrays) to read the exact incoming signal strength and push that identical strength forward across long distances.
  • Decoding the Signal: At the decoder, the incoming line powers a bottom row of dust and a raised row of dust one block further away. Because the top row is one block further from the source, its signal strength is always 1 less than the bottom row right below it.
  • Isolating One Output: Where the signal finally dies out, the bottom dust has a strength of 1 while the top dust right above it has 0. The bottom 1-tick repeater turns off the lower torch, allowing the top output torch to turn on. For all stronger slices before that point, the top dust is also active and sends power through a 2-tick repeater into the top block, keeping those output torches locked off so only a single output activates.

Tips & variations

  • Up to 15 Channels: Because redstone dust has a maximum power level of 15, a single line can support up to 15 distinct inputs and outputs.
  • Turning Corners with Comparators: When using the block-comparator-dust extension method, a single dot of dust weakly powers all four adjacent blocks. You can place a solid block on any side of that dust dot and read through it with a comparator to easily turn 90-degree corners or snake through tight walls.
  • Repeater Chain Alternative: If you only have a few inputs (e.g., 4 to 6) and need to cover a huge distance cheaply, you can place a row of parallel repeaters starting at the last active dust of your weakest input. However, for 10 to 15 inputs, stick to comparators—a 15-wide repeater chain consumes the entire 15-block travel distance just to clear itself.
  • Using Levers Instead of Buttons: If you use levers for constant signals, turning on multiple levers at once will cause the input closer to the output line (the higher signal strength) to override any weaker inputs behind it.

Frequently asked questions

How many inputs can I run on a single redstone line?
You can run up to 15 different inputs and outputs on one line, since the maximum signal strength of redstone dust in Minecraft is 15.
Why can't I just use a normal repeater on the main wire to extend the distance?
A normal redstone repeater boosts any incoming signal back up to a full strength of 15, which wipes out the specific signal strength needed by the decoder to tell which button you pressed. Use comparators to preserve the exact signal strength.
Why are the top repeaters in the decoder set to 2 ticks?
The 2-tick delay ensures the top cancelling signal holds the upper block powered throughout the entire pulse while the bottom 1-tick repeater turns off the lower torch, preventing the wrong outputs from briefly flashing.

Components used

More long distance