
Video: Serial Transmitter & Receiver Tutorial: bedrock edition by Darth_ Dub_
How to build it
- Build the 8-Bit Input Panel
Place a row of 8 solid conductive blocks with 8 Redstone Lamps directly on top of them. Attach a Lever to the front of each solid block to serve as your 8 binary data inputs.
- Attach the Input Sticky Pistons
Go behind the input panel and place 8 Sticky Pistons on the back of the lever blocks facing away. Attach a solid conductive block to the face of each sticky piston.
- Install the Transmitter Observer Chain
Above the extended line where the pushed blocks will land, place a row of 8 Observers facing straight down so their outputs point downward. Add one extra downward-facing Observer at the end, then leave a one-block gap and place a final downward-facing Observer.
- Add the Transmitter Timing Repeaters
Along the top of the main observer row, place Redstone Repeaters on 1-tick delay running from the start of the chain to the end. On the separated observer after the gap, place a Repeater set to 2 ticks and connect the gap using a conductive block and Redstone Dust.
- Create the Send Button Trigger
Extend 3 blocks out to the side of the first input bit. Place a Redstone Lamp on the end block with a Button on the front, and attach a Sticky Piston behind it pushing an upward-facing Observer to generate a short starting pulse into the top repeater line.
- Run the Serial Output Bus
Three blocks below the row of downward-facing observers, build a continuous line of solid blocks running underneath the entire transmitter and lay Redstone Dust across the whole line. Whenever a lever is ON, its block is pushed under an observer so the pulse passes down into this single output wire.
- Extend the Single Transmission Line
Lead the dust line out from under the transmitter through a 1-tick Repeater and extend your single redstone wire as far as needed to reach your receiver site. Use repeaters along the transmission line if your distance exceeds 15 blocks.
- Build the Receiver Gate and Detector
At the receiver end, place an upward-facing regular Piston with a Redstone Block on top, and place a downward-facing regular Piston two blocks above it to reset it. Branch the incoming signal through a 1-tick Repeater up into a block feeding a Repeater in one direction and a Redstone Comparator in the opposite direction.
- Lay Out the 8-Bit Receiver Line
From the receiver entry, place two blocks with Repeaters leading into an alternating line of 8 solid blocks and 8 Repeaters (16 blocks total). Place a Redstone Lamp on top of each of the 8 solid blocks in this chain to display the received bits.
- Install the Repeater Locking Mechanism
Beside each of the 8 lamp blocks in the receiver line, place a solid block with a Repeater facing sideways directly into the side of the main line's repeaters. Behind each of these side repeaters, place an upward-facing regular Piston topped with a Redstone Block so all 8 side repeaters start in a powered, locking state.
- Add the Upper Reset Pistons
Two blocks above the Redstone Blocks on the locking line, place a row of 8 downward-facing regular Pistons. Use a temporary row of guide blocks to align them facing straight down, then break the temporary blocks.
- Wire the Unlock and Re-lock Lines
Run a line of solid blocks and Redstone Dust along the back of the lower upward-facing pistons, and another line of blocks and dust across the top of the upper downward-facing pistons. Connect the upper reset line to the Comparator branch with a Repeater so an incoming transmission immediately pushes the Redstone Blocks down and unlocks the receiver.
- Build the 6-Observer Delay Chain
Connect the lower re-locking piston line via a chain of 6 Observers firing in sequence from the entry trigger into Redstone Dust feeding the bottom pistons. Once all 8 bits have traveled into the receiver repeaters, this delayed pulse pushes the Redstone Blocks back up to lock and display your 8-bit data.
How it works
This circuit encodes parallel data into a serial stream and decodes it back into parallel output using synchronized repeater delays:
- Encoding (Parallel to Serial): Flipping any of the 8 levers extends a sticky piston, placing a solid conductive block directly underneath a downward-facing observer. When you press the Send button, a 1-tick pulse travels down the top repeater chain at 1-tick intervals per bit.
- Transmission: As each observer is triggered in sequence, it fires a pulse downward. If a conductive block is present beneath that observer (representing a binary
1), the pulse passes through the block and powers the lower redstone dust bus. If the piston is retracted (a binary0), an air gap blocks the observer from powering the lower line. - Unlocking the Receiver: The leading pulse travels down the single transmission wire into the receiver. The entry branch immediately fires the top row of downward-facing regular pistons, pushing the Redstone Blocks down. This turns off the side repeaters and unlocks the receiver's main repeater chain.
- Locking the Data (Serial to Parallel): As the 8 bits march in sequence through the receiver's alternating block-and-repeater line, the 6-observer delay line times out just as all 8 bits reach their matching positions. It triggers the bottom upward-facing pistons, pushing the Redstone Blocks back up to power the side repeaters, locking the incoming repeaters and illuminating the corresponding Redstone Lamps.
Tips & variations
- Bedrock Edition Optimization: This design is built specifically for Minecraft Bedrock Edition. In Bedrock, you can run a continuous line of repeaters along the transmission wire without spacing them out, whereas Java and Legacy Console editions require different repeater timings and observer pulse lengths.
- Extending Distance: You can make the single wire between the transmitter and receiver as long as you want (within loaded chunks) as long as you refresh the signal with a 1-tick repeater before the redstone dust exceeds 15 blocks.
- Piston Type Matters: Make sure to use Sticky Pistons for the 8 input levers and button pulse generator, and regular Pistons to push the Redstone Blocks up and down in the receiver.





