Retractable 5x1 Flatground Trap

This retractable 5x1 flatground trap creates a hidden pitfall in completely flat terrain that can be opened and closed automatically without manual rebuilding. It uses a double piston extender array on one side paired with a slime block pulling mechanism on the other to swap floor blocks out of the way. It is ideal for base defense, PvP chases, or pranking friends in Minecraft Bedrock Edition.

Locks & SecurityIntermediateBedrock Edition
Retractable 5x1 Flatground Trap video tutorial

Video: Minecraft Bedrock Edition Retractable 5x1 Flatground Trap by Reality

How to build it

  1. Excavate the Main Pit

    Dig a 10x10 hole that is 4 blocks deep. Go to one corner, count 3 blocks along the wall and 3 blocks inward, and dig a 5-block-long trench downwards to serve as the central drop chute.

  2. Place the Double Piston Extender Stack

    Along the side of the 5-block drop chute that has a 2-block gap from the edge, place a row of 5 crafting tables (or any immovable block) at the bottom. On top of each crafting table, stack two vertical sticky pistons facing upwards (10 sticky pistons total).

  3. Build the Torch Tower

    Behind the bottom row of sticky pistons, place 5 redstone torches on the ground, then place 5 solid blocks directly above those torches. Step one block diagonally up and back to place another row of 5 solid blocks, and put 5 redstone torches on top of them.

  4. Wire the Two Repeater Layers

    On the ground level behind the torch assembly, place a row of 5 redstone repeaters set to 1 tick facing into the blocks, with a line of 5 redstone dust behind them. Place 5 solid blocks above the bottom repeaters, add a second row of 5 repeaters on top set to 2 ticks each, and run 5 redstone dust behind the top row as well.

  5. Add the First row of Surface Blocks

    Place 5 grass blocks (or whatever matches your surrounding terrain) directly on top of the upper row of 5 redstone torches.

  6. Install the Upper Observer Pulse Circuit

    At the end of the repeater lines, place a solid block with redstone dust on top, and point an observer into that dust. Behind the observer, place a solid block, a repeater set to 3 ticks running into another block with dust, and a horizontal sticky piston with a solid block on its face to connect the upper and lower dust lines.

  7. Build the Input and T Flip-Flop Trigger

    Move to the side of the circuit to create the activation input. Place a block with redstone dust on top and attach two redstone torches to its sides. Run two dust from the side torch into a 1-block trench, watch that dust with an observer powering a sticky piston and solid block, and cover the input dust with a surface grass block.

  8. Wire the Slime Retractor Delay Line

    From the input side, dig a small trench wrapping around to the opposite side of the 5-block drop chute. Run 3 redstone dust into a 4-tick repeater, followed by 2 more dust around the corner, and then a chain of three repeaters set to 4 ticks, 4 ticks, and 2 ticks.

  9. Install the Slime Block Floor

    At the end of the delay chain, place two sticky pistons arranged to pull the floor sideways and downward. Place a row of 5 slime blocks across the gap in front of the pistons, and top the slime blocks with 5 grass blocks so they sit flush with the surface.

  10. Place Immovable Borders

    To keep the 5-block slime bar from grabbing adjacent walls, surround its movement path with non-stick immovable blocks. Place two obsidian blocks on each side of the slime row, fill the back wall and bottom supports with crafting tables, and attach 5 signs and 5 banners along the inner lip.

  11. Dig the Hazard Pit and Add Trigger

    Dig out the 5-block-wide drop shaft as deep as you like and line the bottom with pointed dripstone or a hopper collection funnel. Fill in the roof over the redstone with grass blocks so the area is completely flat, and place a pressure plate or lever on the input grass block to test.

How it works

This trap alternates between two states—closed (flush with the ground) and open (exposing the 5x1 pit)—using synchronized piston movements on both sides of the trench:

  • Input Toggle: Stepping on the pressure plate powers the dust beneath the surface block. The observer and sticky piston assembly acts as a toggle/pulse shaper, allowing the trap to open on one activation and cleanly retract and reset on the next.
  • Vertical Double Piston Extenders: On one side of the trench, two stacked rows of repeaters (1-tick on the bottom, 2-tick on the top) together with the 3-tick observer branch invert and sequence the two rows of 5 redstone torches. This fires and retracts the 10 vertical sticky pistons in the exact order needed for a vertical double piston extender in Bedrock Edition.
  • Slime Block Retractor: Meanwhile, the long delay line (three 4-tick repeaters and one 2-tick repeater, totaling 14 ticks) delays the signal to the opposite side of the pit. The two sticky pistons pull the 5-block slime bar and its grass blocks out of the way while immovable blocks (obsidian, crafting tables, signs, and banners) prevent the slime from sticking to the rest of the underground wiring.

Tips & variations

  • Check All Repeater Timings: Before testing, double-check that every single repeater in the double piston extender and the 4-4-4-2 tick delay line is set properly. Even a 1-tick mistake will cause the slime blocks to collide with or stick to the vertical sticky pistons and tear the mechanism apart.
  • Immovable Block Substitutes: The tutorial uses crafting tables and obsidian around the slime blocks because slime cannot pull tile entities or obsidian in Bedrock Edition. You can also use furnaces, smokers, glazed terracotta, or crying obsidian.
  • Bedrock Edition Specific: This wiring relies on Minecraft Bedrock piston timing, block update order, and the ability to move or ignore specific block types; it will not function the same way in Java Edition.

Frequently asked questions

Why are my slime blocks pulling the pistons and breaking the trap?
One or more repeaters are set to the wrong delay. Make sure the upper extender repeaters are all set to 2 ticks, the lower ones to 1 tick, the observer repeater to 3 ticks, and the slime line repeaters to 4, 4, 4, and 2 ticks.
Why are crafting tables, signs, and obsidian used around the pit?
Slime blocks stick to normal solid blocks up to the 12-block push limit. In Bedrock Edition, crafting tables, obsidian, signs, and banners cannot be pulled by slime blocks, keeping the walls intact while the trap moves.
Do I have to reset this trap by hand after someone falls in?
No. Unlike single-use gravel or sand traps, this design is 100% retractable. Triggering the input a second time pushes the grass floor back into place automatically.

Components used

More trap