Intruder Alarm

This intruder alarm protects your base entrance with a two-tone note block siren and a flashing red beacon beam whenever an uninvited player steps inside. Unlike standard lever-operated alarms, it uses a completely hidden hopper minecart toggle so only you know how to arm and disarm the system by dropping an item on a specific floor block.

Locks & SecurityIntermediateJava Edition
Intruder Alarm video tutorial

Video: Minecraft 1.12: Redstone Tutorial - Intruder Alarm v2! by MrCrayfish

How to build it

  1. Set Up the Entrance Door and Pit

    Place your iron door with two-block-tall pillars on both sides and a button on the top-right pillar block. Behind the door, dig a pit that is 5 blocks wide, 8 blocks long, and 3 blocks deep, starting diagonally behind the right-hand door pillar.

  2. Place the Pressure Plate Trigger Dropper

    In the pit, align with the center of the door and place a building block on the floor with redstone dust on top. To the left of this block, place a dropper facing left (away from the block) and attach a hopper feeding directly into the front of that dropper.

  3. Build the Hopper Clock Lock

    To the right of the center redstone dust, place a block, then step back one block and place another block with a repeater coming out of it. After the repeater, place two hoppers facing directly into each other with redstone dust on top of both hoppers.

  4. Add the Trigger Comparator

    Run a redstone comparator out of the left-hand dropper and point it directly into a solid building block positioned next to the two-hopper clock.

  5. Install the Secret Item Collector

    Go to the front-left corner of the pit and dig one block down into the floor to place a chest. Crouch-place a hopper on top of the chest, put a rail on top of the hopper, and set a minecart with hopper on the rail.

  6. Construct the Dropper T Flip-Flop

    Take a comparator output from the hopper beneath the minecart. Skip one block, then build a four-container loop: a bottom dropper facing the comparator, a dropper on top of it facing up or backward into a hopper, and the hopper feeding down into the bottom dropper so an item can cycle between them.

  7. Connect the Arming Line

    Place a comparator reading the bottom dropper of your T flip-flop pointing right into a solid block. Attach a redstone torch to the end of that block, place one redstone dust after the torch, and run a repeater forward into the block under the first trigger hopper.

  8. Wire the Note Block Siren

    Place a comparator coming out of the block beside the two-hopper clock pointing toward the back of the pit. Lead it into a note block, run a repeater (set to 2 ticks) to the left into a second note block, and dig out the blocks directly beneath both note blocks so they play clearly.

  9. Build the Beacon Base

    Dig a 3x3 hole in the floor behind the repeater and comparator area, fill it with 9 iron blocks, and place your beacon in the center so the beam activates.

  10. Add the Flashing Beacon Piston

    To the right of the first note block, place redstone dust leading into a block with a redstone torch on the back. Above that redstone torch, place a sticky piston facing the beacon beam with an opaque block on its face and a red stained glass block on top of the piston arm.

  11. Load Items and Cover the Floor

    Put 1 item inside the trigger dropper, 1 item inside the bottom T flip-flop dropper, and 1 item inside the two-hopper clock. Place a floor block with the stone pressure plate directly above the center redstone dust behind the door, tune your note blocks, and cover the rest of the pit with floor blocks.

How it works

The circuit combines a hidden input, a memory latch, and a locked hopper clock:

  • Secret Input & T Flip-Flop: Dropping an item onto the floor block above the Minecart with Hopper pulls the item through the floor into the hopper and chest below. A comparator detects the item passing through the hopper and pulses the dropper-hopper T flip-flop, toggling the armed state of the alarm.
  • Disarmed State: When disarmed, the T flip-flop comparator turns off the redstone torch line leading to the trigger hopper. Stepping on the pressure plate shoots the item from the trigger dropper into its hopper, and because that hopper is unlocked, the item immediately returns to the dropper. Meanwhile, the pressure plate also powers the repeater locking the two-hopper alarm clock.
  • Armed & Triggered State: Throwing another item toggles the T flip-flop, turning on the redstone torch and locking the trigger hopper. When an intruder steps on the pressure plate, the trigger dropper shoots its item into the locked hopper where it gets trapped. The comparator reading that dropper turns off, unlocking the two-hopper clock. Once the intruder steps off the pressure plate, the item in the two-hopper clock bounces back and forth continuously.
  • Siren & Strobe Output: A comparator reads the bouncing item in the hopper clock, sending a rapid pulse through the two Note Blocks and toggling the Sticky Piston. The piston repeatedly pushes a solid block into the Beacon beam (blocking it) while shifting the Red Stained Glass over the beam, creating a flashing red strobe effect.

Tips & variations

  • Arming and Disarming Safely: To arm the alarm before leaving, stand on the pressure plate first, throw an item onto the secret corner block, and walk out the door. When returning home, step onto the pressure plate, throw an item onto the secret block to disarm it, and only then step off the plate into your base.
  • Beacon Sky Access: You can hide the beacon inside a wall, pillar, or chimney, as long as the beam itself has an unobstructed path to the sky (or through transparent blocks like glass).
  • Custom Siren Pitch: Right-click the two note blocks to two different pitches (for example, 5 clicks and 8 clicks) and set the repeater between them to a 2-tick delay for an alternating two-tone alarm sound.

Frequently asked questions

How do I enter my own house without setting off the alarm?
Walk through the door and stay standing on the pressure plate. While still on the plate, drop any item onto the secret corner block above the hopper minecart to disarm the system, then walk inside.
Why does the beacon take a few seconds to change or turn off?
Minecraft beacons update their beam color and sky-access check on a brief game-tick interval rather than instantaneously, so the piston blocking and unblocking the beam creates a steady flashing strobe.
Why do we need to break the blocks underneath the note blocks?
The block below a note block determines which instrument sound it plays, and digging it out prevents muffled or unwanted percussion sounds depending on your floor material.

Components used

More alarm / intruder detector