Double Piston Extender for 3x3 Doors

Building a 3x3 piston door requires a way to push and pull the very center block into place without leaving visible pistons behind. This vertical double piston extender paired with a side storage piston solves the hardest part of a 3x3 door by pushing the center and bottom-middle blocks up when closing, and tucking the extra block away when opening.

Piston ContraptionsIntermediateJava Edition
Double Piston Extender for 3x3 Doors video tutorial

Video: 3x3 Piston Door Mechanics | Double piston extender by Wifies

How to build it

  1. Prepare the 3x7 foundation and input

    Clear a 3x7 working area that is about 3 blocks deep below your desired floor level. Go to the third block along the edge, come two blocks in and two blocks up to mark your floor level, and attach a lever to that block.

  2. Build the dropper-hopper unit

    In the corner of your platform, place a dropper facing straight up with a hopper directly on top of it pointing down into the dropper. Put 1 random item inside the dropper.

  3. Wire the comparator and rail

    Place a line of redstone dust leading from beneath your lever block to the dropper, and place a detector rail next to that dust. Behind the hopper, place a redstone comparator reading from the hopper into a solid block.

  4. Place the redstone torches and side piston

    Place a solid block diagonally up above the detector rail and attach a redstone torch to its side, then place another block and redstone torch above to invert the signal. Next to the comparator's output block, place a horizontal sticky piston facing inward to pull a solid block across the line.

  5. Install the double extender and storage pistons

    Stack two sticky pistons facing straight up in the center column of your future doorway, and place a third sticky piston to the side facing horizontally into the space right above the vertical stack. Place your two door blocks on the top vertical piston and the horizontal storage piston.

  6. Add the 4-tick repeater and observer

    Run redstone dust and a 1-tick repeater from the lower circuit toward the pistons. Place a second repeater set to 4 ticks running directly into the face of an observer so the observer outputs a pulse toward the back of the vertical piston stack.

  7. Complete the upper 3-tick pulse loop

    Behind the observer, place redstone dust leading up onto a solid block. Run a repeater set to 3 ticks (two right-clicks) from that block into another block with redstone dust on top, and place a block with redstone dust above the repeater to power the extended top piston during retraction.

How it works

This mechanism handles both the double extension and the block-swapping sequence needed for the bottom-center of a 3x3 door:

  • 1-Tick Block Spit (Closing): In Java Edition, when a sticky piston receives a 1-tick pulse, it pushes its block out and immediately retracts without pulling the block back. The horizontal storage piston uses a 1-tick pulse cut off by a moving block to spit the extra door block directly over the vertical double piston extender.
  • Double Extension: The bottom vertical piston pushes the top vertical piston (and the first door block) upward. After the horizontal piston deposits the second door block into the gap, the bottom vertical piston fires a second time to push that block up into the doorway.
  • Double Retraction (Opening): When the lever is toggled off, the bottom piston retracts first while the horizontal storage piston briefly grabs the bottom door block out of the way. The 4-tick repeater, observer, and 3-tick repeater loop then send a delayed pulse to push the bottom piston up into the top piston and power it at the upper position, pulling the center door block all the way down to floor level.

Tips & variations

  • Java Edition Only: This build relies heavily on sticky pistons dropping their blocks on a 1-tick pulse, which is a mechanic exclusive to Minecraft Java Edition.
  • Expanding to a Full 3x3 Door: Because this tutorial focuses on the core bottom-center mechanism, you can easily wire the remaining side and top door pistons by running observers or redstone lines off the main redstone torch tower.
  • Check Repeater Delays: If the top center block gets stuck floating in mid-air when opening the door, double-check that your bottom repeater leading into the observer is on 4 ticks and the upper repeater is on 3 ticks.

Frequently asked questions

Why do you need a third sticky piston on the side of the double extender?
A vertical double piston extender can grab and pull a block from two spaces up, but it cannot store two door blocks stacked on top of it when retracted. The horizontal sticky piston pulls the lower door block to the side so the vertical extender has a clear path to reach the center block of the 3x3 door.
Does this double piston extender work in Minecraft Bedrock Edition?
No. The storage piston and double extender rely on 1-tick block spitting—where a sticky piston leaves its block behind after a 1-tick pulse—which only works in Minecraft Java Edition.
How deep below the floor does this circuit need to be?
The circuit sits 3 blocks deep below your floor level on a 3x7 platform so the retracted pistons and wiring stay completely hidden beneath the doorway.

Components used

More piston extender